Instrukcja obsługi Lorex ACCYARD1
Lorex
nieskategoryzowany
ACCYARD1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lorex ACCYARD1 (1 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 22 osób i została oceniona przez 11.5 użytkowników na średnio 4.2 gwiazdek
Strona 1/1
Package Contents
• Yard Sign with Solar LED Light and Rechargeable Battery
• Mounting Screws & Drywall Anchors (×2)
• Sign Post (3 pieces; 1 pre-attached to sign)
Dimensions
9.2"
233mm
11.8" / 300mm
Installation (YARD SIGN)
Getting Started
• Before installing the sign, press the power button on the underside of the solar
LED light. This will allow the battery to charge during the day and turn on the
light at night. It is recommended to check that the light comes on in a dark room
before installing the sign.
• Choose a location for the sign with plenty of direct sunlight exposure. Do not
install in a covered or shaded area.
• The solar panel requires at least 3-4 hours of direct sunlight per day.
Performance dependent on temperature and light exposure.
• For wall mounting, ensure you can safely drill into your selected mounting
location.
33.6"
853mm
1. Wearing protective
work gloves, push the
pointed end of Bar #3
into the ground. The
pointed side of the
bar should point the
opposite direction that
the sign will face.
NOTE: If the ground is
especially solid, tap the
bar into place using a
rubber mallet.
2. Press the spring-
loaded button on the
bottom of Bar #2 to
insert into the top of
Bar #3. Be careful not
to pinch your fingers
between the bars.
3. Press the spring-
loaded button on the
top of Bar #2 to insert
into the top of Bar #1
(pre-attached to the
back of the sign). Be
careful not to pinch
your fingers between
the bars.
To install the sign in the ground:
ATTENTION:
Choose a location for the sign with plenty of direct sunlight exposure.
Do not install in a covered or shaded area.
Bar #2
Bar #3
Bar #1
Spring-loaded
buttons
Installation (WALL SIGN)
To install the sign on a wall:
ATTENTION:
Choose a location for the sign with plenty of direct sunlight exposure.
Do not install in a covered or shaded area.
1. Remove the fastening
screws (see ) Figure 2
from the front of the
sign using a Phillips
head screwdriver (not
included). This removes
the back bar
to prepare the sign for
wall-mounting.
2. Drill holes for the
mounting screws and
plastic anchors (×2). The
holes must be level and
4.25” (108mm) apart
center-to-center.
3. Insert the anchors
firmly into the holes
(recommended to tap
anchors into place using
a rubber mallet).
4. Use a Phillips
screwdriver to insert
the mounting screws
into the anchors. Leave
approximately 5mm of
each screw outside of
4.25"
108mm
Mounting surface
Mounting
screw
Plastic
anchor
5mm
Mounting
screws (×2)
Plastic
anchors (×2)
Fastening
screws (×2)
Pointed side should face
the opposite direction of
the sign
*
* Side view
Figure 1 Figure 2
Figure 3
5. Line up the notches on the back of the solar LED light with
the protruding screws and push down on the sign to secure
it in place.
the anchor (see ).Figure 3
Safety Precautions
• The solar panel may require periodic cleaning to ensure it is capturing light
effectively. Use a damp cloth only. Do not use chemical cleaners.
• Do not dispose of the battery in regular garbage. Handle as hazardous waste.
Dispose according to local hazardous waste programs.
ACCYARD1_QSG_EN_R2
Copyright © 2018 Lorex Corporation
As our products are subject to continuous improvement, Lorex
reserves the right to modify product design, specifications and
prices, without notice and without incurring any obligation.
E&OE. All rights reserved.
www.lorex.com
Quick Start Guide Security Yard Sign
ACCYARD1
Specyfikacje produktu
| Marka: | Lorex |
| Kategoria: | nieskategoryzowany |
| Model: | ACCYARD1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Lorex ACCYARD1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje nieskategoryzowany Lorex
4 Lipca 2024
19 Czerwca 2024
19 Czerwca 2024
19 Czerwca 2024
19 Czerwca 2024
19 Czerwca 2024
19 Czerwca 2024
19 Czerwca 2024
19 Czerwca 2024
19 Czerwca 2024
Instrukcje nieskategoryzowany
- Sungrow
- Alpine
- Fujifilm
- Waterdrop
- Dangerous Music
- SmallRig
- Fontastic
- Lumens
- FiiO
- Sonifex
- Arthur Martin
- Bogen
- EVOline
- Hoberg
- Multibrackets
Najnowsze instrukcje dla nieskategoryzowany
28 Października 2024
28 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024