Instrukcja obsługi MB Quart FA2-400.4
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla MB Quart FA2-400.4 (2 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 4.7 gwiazdek
Strona 1/2
External 40A
External 100A
External 80A
External 100A
External 125A
Place terminal in a secure
position so that it won’t
accidentally contact the
negative battery post
Power cable size
and fusing
It is critical to use the proper power
and ground cable. Select the size
listed here for your amplier model.
Always use high quality copper
cable. Visit our website for multi amp
system cable recommendations.
Be sure to use the proper fuse size
for each model.
Properly route power,
speaker and RCA cables
through the vehicle.
Choose a mounting location
that will provide adequate air
ventilation. Mount the amplier to
a secure surface. Do not mount
the amplier upside down.
Attach the chassis ground
cable to the amplier
negative terminal. It is
important to make sure this
connection is very tight.
Bare metal
Attach the main power cable
to the amplier +12V. The
cable must run directly to
the battery and be properly
fused and be very tight.
Attach the remote turn on
wire to the amplier remote
output of the source unit.
Connect the RCA cables to the
coordinating RCA input number
that will match the speaker
outputs number.
Connect the power cable to the
positive battery terminal. The
power cable must be fused
within 18 inches of the battery
terminal.
Re-connect the negative
battery terminal making sure it
is securely tightened.
The chassis ground connection
is critical to the performance
of the amplier. Choose a
location that is close to the
amplier. Completely scrape
away the paint and use a nut
and bolt if possible.
DO NOT USE AN EXISTING
FACTORY BOLT!
Disconnect
negative battery
terminal
Run Cables
Mount Amplier
Negative Power
Connection
Positive Power
Connection
Remote Turn-on
Connection
Signal Input
Connection
Positive Battery
Connection
Re-connect
Negative Battery
Terminal
Chassis Ground
Be prepared to disarm your vehicle’s alarm and
to enter your radio / source unit code.
Installation
Before you start
CAUTION
Many new and factory radios require a reset code when
disconnected from battery power. This is an anti-theft
feature. Before unplugging power, you must determine if
your radio/source unit requires a reset code. Check the
operation manual for your vehicle or contact the dealer.
1
2
3
5
7
6
8
11
12
4
POWER
REM turn on (Remote wire turn on)
when using High Level Input
- DC turn on
- Signal Sense turn on
Auto-Sense
Technical Guide
Turn on Mode
9
Model Fuse Size Cable Size
4ga
FA2-400.4
FA2-900.5
FA2-1000.1
FA2-1500.1
FA2-2000.1
Using spade terminals,connect
the speaker cables to the speaker
output connectors. Follow the
diagram below that best ts your
speaker conguration.
Speaker
Connections
Stereo
Monoblock
single woofer multiple woofersMonoblock
Bridged
10
CH1 CH2
SPEAKER
SPEAKER
REM
ON
DC
ON
SIGNAL
ON
MODE
NOTE - If the RCA’s are plugged into the amplier and the TURN ON MODE is in the
DC ON position, the amplier will NOT turn on. Please re-read QR document above or
hire a professional installer.
Specyfikacje produktu
| Marka: | MB Quart |
| Kategoria: | odbiornik |
| Model: | FA2-400.4 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z MB Quart FA2-400.4, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik MB Quart
29 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
29 Marca 2025
7 Października 2024
18 Września 2024
6 Września 2024
5 Września 2024
28 Sierpnia 2024
Instrukcje odbiornik
- Seco-Larm
- DLS
- Insignia
- Samson
- ATen
- OSD Audio
- JETI
- Primare
- Phonic
- Mtx Audio
- Shure
- Motorola
- Sonance
- IRiver
- Lindell Audio
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025