Instrukcja obsługi Microchip MIC4812YMME
Microchip
nieskategoryzowany
MIC4812YMME
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Microchip MIC4812YMME (4 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 3 użytkowników na średnio 4.8 gwiazdek
Strona 1/4
MIC4812 Evaluation Board
High Current 6 Channel Linear WLED
Driver with DAM™ and Ultra Fast
PWM™ Control
Ultra Fast PWM and DAM™ Dynamic Averagie Matching are trademarks of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
General Description
The MIC4812 is a high efficiency linear White LED
(WLED) driver; it is designed to drive up to six high current
WLEDs while maintaining constant current in each
channel. The MIC4812 features Dynamic Average
Matching™ (DAM™) which is specifically designed to
provide optimum matching across all WLEDs. These high
accuracy (±1% typical) current regulated WLED channels
ensure uniform display illumination under all conditions. A
typical dropout of 190mV at 100mA is expected.
The MIC4812 is available in a 10-pin Epad MSOP
package with a junction temperature range of -40°C to
+125°C.
Datasheets and support documentation can be found on
Micrel’s web site at: www.micrel.com
Requirements
The MIC4812 evaluation board requires a power supply
that is capable of delivering at least 1A while providing an
input voltage between 3.0V and 5.5V.
Precautions
The MIC4812 evaluation board is designed for an input
voltage no greater than 6V. This evaluation board does not
have reverse polarity protection; hence, applying a
negative voltage to the VIN terminal may damage the
device.
Getting Started
1. Connect an external supply to VIN. Apply the
desired input voltage across VIN and ground
terminals, J1 and J2, respectively, paying careful
attention to polarity and supply voltage
(3.0V≤VIN≤5.5V). An ammeter may be placed
between the input supply and the VIN terminal to
the evaluation board. Ensure that the supply
voltage is monitored at the VIN terminal. The
ammeter and/or power lead resistance can reduce
the voltage supplied to the input.
2. Enable/Disable the MIC4812
To enable the device, apply a DC voltage of 1.2V or
greater to the EN pin (J3). This allows for full
brightness of the WLEDs (100% duty cycle). The EN
pin can also be used for dimming by connecting a
PWM signal and varying its duty cycle (please refer to
the Ultra Fast PWM™ Dimming Interface Section in
datasheet). Pulling EN low for more than 20ms forces
the MIC4811 into a low IQ sleep mode. Do not leave
the EN pin floating as this may cause an indeterminate
output state. A pull down resistor of 200kΩ is placed from
EN to GND to ensure that the WLEDs are OFF when an
enable signal is not applied.
3. Setting LED current with RSET resistor.
The average LED current may be calculated using the
equation below:
( )
139.0)(
820
)(
139.0
)(
820
)(
−Ω
⋅
=
+
⋅
=Ω
kR
D
mAI
mAI
D
kR
SET
LED
LED
SET
D is the duty cycle of the LED current during PWM
dimming; D=1 when device is fully ON. The stock
evaluation board uses an RSET value of 8.25kΩ which
corresponds to ILED of 10mA.
4. Measuring WLED current.
To measure WLED current, simply insert an ammeter
in series with the WLED(s). Keep in mind that a series
ammeter will add a small voltage drop, so the voltage
at the WLED terminal(s), D1-D6, should be used when
making dropout measurements with a series ammeter.
Ordering Information
Part Number Description
MIC4812YMME EV Evaluation board with Six Channel
WLED Driver
March 2011 M9999-032111-B
Specyfikacje produktu
| Marka: | Microchip |
| Kategoria: | nieskategoryzowany |
| Model: | MIC4812YMME |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Microchip MIC4812YMME, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje nieskategoryzowany Microchip
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
5 Lipca 2024
Instrukcje nieskategoryzowany
- Aguilar
- RTS
- Adidas
- Merging
- Goki
- Rio
- Thomson
- Aerotec
- Trust
- Dyson
- Vivolink
- Stages
- Expressive E
- Technika
- Belkin
Najnowsze instrukcje dla nieskategoryzowany
28 Października 2024
28 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024