Instrukcja obsługi Monacor PREAMP-1UP

Monacor Kontroler PREAMP-1UP

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Monacor PREAMP-1UP (2 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 9 użytkowników na średnio 4.8 gwiazdek

Pobierz PDF

Strona 1/2

Technical data S.1/2

Preamplifier PREAMP

Technical modifications reserved 07/04

Thank you for buying a WHD product. Please read this manual carefully,especially the ! marked parts.

Content :

PREAMP CD500 uP ... :

Pre-Amplifier with metal front plate. Plastic front plate with printing.Plasic rotary knobs.Accessory subframe

CD500 ,colour : “ alpinweiss “

PREAMP uP ... :

Pre-Amplifier with metal front plate. Plastic front plate with printing.Plasic rotary knobs.

Colour : “ alpinweiss “

The subframes are not available at WHD.

PREAMP BJ uP ... :

Pre-Amplifier with metal front plate. Plastic front plate with printing.Plasic rotary knobs.

Colour : “ alpinweiss “

The subframes are not available at WHD.

Specifications :

Supply voltage : 22-26V

Output voltage : 5V max.

Output impedance : 50 Ω

Input voltage Line : 400 mV

Input voltage Mic : 4mV

Frequency range Line : 20-20 000 Hz (-1dB)

Frequency range Mic : 40-15 000 Hz (-3dB)

Current consumption : 0,025 A

Terminal : 7 -pole terminal , removeable

Control voltage : 0-10VDC

Additional parts : ( JUNG/CD500 frames and UP-cabinets KAISER available at WHD)

Subframe Frame

single Frame

double UP-cabinet

61/63 mm

X X X

The microphone volume control has a combined ON-OFF switch.

Technical data - S. 2/2 - Pre- amplifier PREAMP ...

Technical modifications reserved 07/04

Mounting :Mounting :

Connect terminal according to wiring scheme.

Backside view

Note : The control terminal no. 4 gets a voltage of 12V by an internal resistor. So the preamplifier

has the maximum gain at open terminal.

Terminal no

1 + Signal – out ( unbalanced )

2 0 Signal

3 Reduced gain

4 + Control input 0-12 VDC

5 0 V Control

6 0 Supply voltage

7 + 24V Supply voltage

8 0 V Phantom / Mic

9 + Mic input

10 + 24V Phantom

If the gain is too high for some applications , connect the accessory wire bridge to terminal 3 and 5.

This will reduce the gain to app. 1/3.

Note : Teminal 8 to 10 is only for use with input balance unit.

For the signal and control line we recommend shielded cable.

e.g. LIYCY 0.14mm² 2-cores

The cross section of the power supply cable should be adequate.

e.g. H03VV-F 0,5mm² 2-cores

We recommend regulated 24VDC power supply with short circuit protection.

Specyfikacje produktu

Marka:	Monacor
Kategoria:	Kontroler
Model:	PREAMP-1UP
Kolor produktu:	Biały
Napięcie operacyjne wejścia (maksymalne):	0.4 V
Model:	Obrotowa regulacja głośności
Typ mocowania:	Do zawieszenia na ścianę
Zasięg częstotliwości:	20 - 20000 Hz
Impedencja wyjścia:	50 Ω
Utrzymywanie mocy:	- W