Instrukcja obsługi Motorola Talkabout T482
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Motorola Talkabout T482 (2 stron) w kategorii radio. Ta instrukcja była pomocna dla 19 osób i została oceniona przez 10 użytkowników na średnio 4.6 gwiazdek
Strona 1/2
m
TALKABOUT ® EMERGENCY
PREPAREDNESS TWO-WAY
RADIO T48X Series
*MN001399A01*
MN001399A01-AG
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks
or registered trademarks of Motorola Trademark Holdings, LLC and are used under
license. All other trademarks are the property of their respective owners.
© 2015 and 2020 Motorola Solutions, Inc. All rights reserved.
Printed in
For More Information
For further information, you may call Motorola Solutions at
1-800-448-6686 (Canada and U.S.), or visit us on the Internet at
www.motorolasolutions.com/talkabout.
Caution
Before using this radio, read this booklet which contains
important operating instructions.
For information on product details, brochures, user manuals and
approved accessories. Please refer to
www.motorolasolutions.com.
Compliance with RF Exposure Standards
National and international regulations require manufacturers to
comply with the RF energy exposure limits for portable two-way
radios before they can be marketed. Your Motorola Solutions
two-way radio is designed, manufactured, and tested to comply
with all applicable national and international regulations for
human exposure to radio frequency electromagnetic energy.
RF Energy Exposure Awareness and Control Information
and Operational Instructions for General Population and
Uncontrolled Environment Use
For more information on what RF energy exposure is, see the
following websites:
• https://www.fcc.gov/
• http://www.who.int/peh-emf/project/en/
•http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf11467.html
•http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01904.html
For additional information, see
https://www.motorolasolutions.com/en_us/about/company-
overview/corporate-responsibility/governance-and-policies.html
Class B Digital Device
For a Class B digital device or peripheral, the instructions
furnished the user shall include the following or similar
statement, placed in a prominent location in the text of the
manual:
Note:This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Operating Instructions
• Transmit no more than 50% of the time. To transmit (talk),
press the Push-To-Talk (PTT) button. To receive calls, release
the PTT button.
• Hold the radio in a vertical position in front of the face with the
microphone (and other parts of the radio including the
antenna) at least 1 in. (2.5 cm) away from the nose or lips.
Antenna should be kept away from the eye.
• When worn on the body, always place the radio in a Motorola
Solutions-approved clip, holder, holster, case, or body
harness for this product.
• DO NOT hold the antenna when the radio is transmitting.
• DO NOT use any portable radio that has a damaged antenna.
If a damaged antenna comes into contact with your skin, a
minor burn can result.
• To ensure continued compliance with applicable RF exposure
limits, use only Motorola Solutions-approved, supplied or
replacement antennas, batteries, and accessories.
• For a list of Motorola Solutions-approved accessories please
refer to your user manual or visit www.motorolasolutions.com
Acoustic Safety
Exposure to loud noises from any source for extended periods
of time may temporarily or permanently affect your hearing. The
louder the volume of the radio, the sooner your hearing will be
affected. Hearing damage from loud noise is sometimes
undetectable at first, and can have a cumulative effect.
To protect your hearing, follow these precautions:
• Use the lowest volume necessary to do your job.
• Turn up the volume only if you are in noisy surroundings.
• Turn down the volume before putting on a headset or
headphones.
• Limit the amount of time you use a headset or headphones at
high volume.
• When using the radio without a headset or headphones, do
not place the speaker of the radio directly against your ear.
Medical Devices
If you use a personal medical device, such as a pacemaker or
hearing aid, consult the manufacturer of your device to
determine if it is adequately shielded from RF energy. Your
physician may be able to assist you in obtaining this information.
Operational Warnings
The following explains the operational warnings:
For Vehicle With Air Bags
Potentially Explosive Atmospheres
Blasting Caps and Blasting Areas
Batteries
• Charge your battery using the approved Motorola Solutions
charger.
• Use the battery in accordance with its water and/or dust
Ingress Protection (IP) rating.
• Do not discard your battery into a fire.
• Do not replace the battery in any area labeled “Hazardous
Atmosphere”.
• Do not disassemble, crush, puncture, shred, or otherwise
attempt to change the form of your battery.
• Do not dry a wet or damp battery with an appliance or heat
source, such as a hair dryer or microwave oven.
• Do not allow conductive material such as jewelry, keys, or
beaded chains to touch exposed battery terminals.
Do Not Substitute Options or Accessories
The Motorola Solutions communications equipment certified as
intrinsically safe by the approving agency (FM, UL, CSA,
CENELEC) is tested as a complete system which consists of the
listed agency approved portable, approved battery, and
approved accessories or options, or both. This approved
portable and battery combination must be strictly observed.
There must be no substitution of items, even if the substitute
has been previously approved with a different Motorola
Solutions communications equipment unit. Approved
configurations are listed by the approving agency (FM, UL,
CSA, CENELEC).
The Intrinsically Safe Approval Label affixed to radio refers to
the intrinsically safe classification of that radio product, and the
approved batteries that can be used with that system.
The manual PN referenced on the Intrinsically Safe Approval
Label identifies the approved accessories and or options that
can be used with that portable radio unit.
Using a non-Motorola Solutions-intrinsically safe battery and/or
accessory with the Motorola Solutions-approved radio unit will
void the intrinsically safe approval of that radio unit.
European Union (EU) Waste of Electrical and
Electronic Equipment (WEEE) Directive
Supplier’s Declaration of Conformity
Notice to Users (FCC and Industry Canada)
This device complies with Part 15 of the FCC rules and Industry
Canada's license-exempt RSS's per the following conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including
interference that may cause undesired operation.
• Changes or modifications made to this device, not expressly
approved by Motorola Solutions, could void the authority of
the user to operate this equipment.
USA (FCC)/CANADA
According to FCC Part 95, FRS devices do not require a
license. Use of Motorola radio in Canada is subject to the rules
regulations in ISED RSS 210 and do not require a license.
Changes or modifications not expressly approved by Motorola
Solutions may void the user authority granted by the FCC or
ISED to operate this radio and should not be made. To comply
with FCC or ISED requirements, transmitter adjustments should
be made only by or under the supervision of a person certified
as technically qualified to perform transmitter maintenance and
repairs in the private land mobile and fixed services as certified
by an organization representative of the user of those services.
Replacement of any transmitter component (crystal,
semiconductor, etc) not authorized by the FCC or ISED
equipment authorization for this radio could violate FCC or ISED
rules.
Note:Use of this radio outside the country where it was intended
to be distributed is subject to government regulations and
may be prohibited.
Weatherproof
This radio is weatherproof to IP-54 standards. It is dust/
splashproof from any direction. The radio is resistant to water
and rain splashes only when the battery cover, headset
accessory port, and micro-USB ports are sealed. Open the
battery compartment door or headset port cover only when the
radio is dry. Use of a headset accessory should be in dry
environments only.
The micro-USB adaptor is not waterproof. Do not expose to rain
or snow. Charge the radios only in a dry location. Do not charge
wet radios. The battery door must be tightly closed with the
screw to maintain the weatherproof seal of the radio.
Installing the Batteries
Each radio can use either 1 NiMH rechargeable battery pack or
3 AA alkaline batteries and beeps when the batteries are low.
Installing the NiMH Rechargeable Battery Pack
(Optional Accessory)
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door and open the cover.
3. Remove the NiMH battery pack from the clear plastic bag
(do not disassemble or unwrap the battery pack).
4. Insert the NiMH battery pack with the diagram facing you.
(The ribbon should be underneath the battery pack and
should wrap around the right side of the pack for easy
removal).
5. Close the battery cover and tighten the retaining screw on
the battery cover.
Installing the Three AA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, lift the battery cover
latch up and remove the cover.
3. Insert the three AA Alkaline batteries with + and – polarity as
shown inside. (The ribbon should be underneath the AA
alkaline batteries and should wrap around the right side of
the batteries).
4. Close the battery cover and tighten the retaining screw on
the battery cover.
Radio Battery Meter
The radio battery icon shows the battery charge level, from full
to empty . When the radio has one segment left,
the radio chirps periodically or after releasing the PTT button
(Low Battery Alert).
Removing Battery Door and Belt Clip
1. Use your thumb or index finger to unlatch the belt clip tab,
use thumb on another hand to push up the belt clip.
2. Use a coin to unscrew the battery door screw lock.
Removing the NiMH Battery Pack
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door and open the cover.
3. Remove the NiMH battery pack by pulling the ribbon
attached to the radio.
4. Close the battery cover and tighten the retaining screw on
the battery door.
Removing the Three AA Alkaline Batteries
1. Turn the radio off.
2. With the back of the radio facing you, loosen the retaining
screw on the battery door and open the cover.
3. Gently remove each alkaline battery by easing each battery
out individually.
4. Close the battery cover and tighten the retaining screw on
the battery door.
Note:
• Exercise care when removing NiMH or AA batteries. Do not
use sharp or conductive tools to remove either of these
batteries.
• Remove the batteries before storing your radio for extended
periods of time. Batteries corrode over time and may cause
permanent damage to your radio.
Battery Capacity Maintenance
1. Charge the NiMH batteries once every 3 months when not in
use.
2. Before placing the radio in storage, remove the battery.
3. Store the NiMH batteries in temperature between -20 °C to
35 °C and in low humidity. Avoid damp conditions and
corrosive materials.
Using the Micro-USB Charger
The micro-USB charger is a handy port that allows you to
conveniently charge your NiMH battery pack.
1. Make sure your radio is turned OFF.
2. Plug the micro-USB cable into the micro-USB charging port
on your radio.
3. Connect the USB charger to a nearby and easily accessible
wall power outlet.
4. An empty battery will be fully charged in 14 hours.
5. The battery meter on LCD will move to indicate the battery is
charging.
Note:
• When moving between hot and cold temperatures, do not
charge the NiMH battery pack until the battery temperature
acclimates (usually about 20 minutes).
Using the Desk/Wall Stand
This stand allows for convenient placement during charging (on
desk or hung on wall). Cable management can be achieved via
cavity at bottom of stand.
1. Determine the required cable length.
2. Place rolled up cable with cable tie into stand around the two
latches following markings for correct orientation.
Note: For alternate lengths, wrap cable around approximately 3
fingers for correct loop size.
3. Assemble bottom cover on stand.
Quiet Charge
In order to ensure that your radio is always charged and on
alert, we recommend that you leave the radio plugged in and
turned on. The Quiet Charge feature allows you to disable the
reception from regular two-way calls while still receiving weather
alerts and receive and transmit emergency alerts.
To activate quiet charge:
1. Press 9 times until appears on the display. The
current setting will flash.
2. Press or to select On or Off.
3. Press the PTT button or to set.
Note: Turn Quiet Charge off when you want to have full two-way
call functionality (receive all activity on your channel).
Attaching and Removing the Belt Clip
1. Attach the belt clip to the Talkabout plate at the back of the
radio until the clip clicks in place.
2. Attach the belt clip to pocket or belt strap until the clip clicks
in place.
To Remove
1. Pull the release tab on top of the belt clip to release the latch.
2. Push the belt clip with the other hand towards the top of the
radio.
Turning your Radio On and Off
Turn clockwise to turn the radio on and counterclockwise to
turn the radio off.
1. In the ON position, the radio chirps and briefly shows all
feature icons available on the radio.
2. The display screen then shows the current channel, code
and all features that are enabled. The radio is now in
Two-Way mode.
Setting the Volume
Press and hold for three seconds while rotating until you
reach a comfortable listening level.
1. Rotate clockwise to increase the volume.
2. Rotate counterclockwise to decrease the volume.
Do not hold the radio close to your ear. If the volume is set to an
uncomfortable level, it could hurt your ear.
To communicate, all radios in your group must be set to the
same channel and Interference Eliminator Code.
1. To talk, press and hold the PTT button. When transmitting,
icon blinks and is shown. If it is a high
power transmission, is shown. If it is a low power
transmission, is shown.
2. When you are finished talking, release the PTT button.
3. When receiving, icon blinks and is shown.
If it is a high power channel, is shown. If it is a low power
channel, is shown.
For maximum clarity, hold the radio two to three inches away
from your mouth and speak directly into the microphone. Do not
cover the microphone while talking.
Note: The use of an emergency two-way radio is best when
other people in your community are using two-way radios
as well. Talk to neighbors and friends nearby and suggest
to check in on each other when disaster strikes.
Talk Range
Your radio is designed to maximize performance and improve
transmission range. Do not use the radios closer than five feet
apart.
Power Boost
To boost your radio’s power up to high power, press the top
portion of the PTT button when talking. If you know your party is
close by, you can conserve the energy of your battery by
pushing the lower part of the PTT button to use less power.
Note: If you are on an FRS only channel (see “Channels and
Frequencies”) the radio will only use low power when
either portion of the PTT button is pressed.
Power Boost is not applicable for model T400.
Monitor Button
Pressing and holding for three seconds allows you to listen
to the volume level of the radio when you are not receiving. This
allows you to adjust the volume, if necessary. You can also
press to check for activity on the current channel before you
talk.
Push-to-Talk Timeout Timer
To prevent accidental transmissions and save battery life, the
radio emits a continuous warning tone and stops transmitting if
you press the PTT button for 60 continuous seconds.
Mode Button
By pressing “mode” button, the user will be seamlessly
switching between two-way, weather mode and FM mode.
When radio is in two-way mode, will be shown.
When radio is in weather mode, will be shown.
Corresponding setting and information will be shown on the
LCD.
Selecting the Channel
Your radio has 22 channels. The channel is the frequency the
radio uses to transmit. Channels 8-14 are FRS 0.5 watt only and
all other channels are GMRS. (See the “Channels and
Frequencies” table on overleaf for details).
1. With the radio on, press 1 time until the channel number
starts to flash. When the radio is on a 0.5 watt channel,
display shows . When the radio is on a 1.5 watts
channel, display shows . The current channel flashes.
2. Press or and select an unused or quiet channel.
3. Press the PTT button to save the channel setting or to
continue set up.
Selecting the Interference Eliminator Code
Interference Eliminator Codes help minimize interference by
blocking transmissions from unknown sources. Your radio has
121 Interference Eliminator Codes. Codes 1 – 38 are standard
analog codes that appear on other FRS/GMRS radios. Codes
39 – 121 are additional digital codes added for superior
interference protection. 0 is the off position, no analog or digital
codes are enabled.
To set the code for a channel:
1. Press 2 times until the code starts to flash.
2. Press or to select the code.
Safety and General Information
Warning:
• Refer to vehicle manufacturer's manual prior to
installation of electronic equipment to avoid
interference with air bag wiring.
• DO NOT place a portable radio in the area over an
air bag or in the air bag deployment area. Air bags
inflate with great force. If a portable radio is placed in
the air bag deployment area and the air bag inflates,
the radio may be propelled with great force and cause
serious injury to occupants of the vehicle.
Warning:
• Use of a radio that is not intrinsically safe in a
potentially explosive atmosphere could result in a
serious injury, or death. You should only use a
certified Intrinsically Safe radio in potentially
explosive atmospheres.
• Explosive atmospheres refer to hazard classified
locations that may contain hazardous gas, vapors,
dusts, such as fueling areas below decks on boats,
fuel, or chemical transferor storage facilities, and
areas where the air contains chemicals or particles
such as grain, dust, or
metal powders. Areas with potentially explosive
atmospheres are often, but not always, posted.
• Turn off your radio prior to entering any area with a
potentially explosive atmosphere unless it is a radio
type specifically certified for use in hazardous
location areas.
• DO NOT remove, install, or charge batteries in such
areas, or remove or install antennas. Sparks in a
potentially explosive atmosphere can cause an
explosion or fire resulting in bodily injury or even
death.
Warning: To avoid possible interference with blasting
operations, turn off your radio when you are near
electrical blasting caps, in a blasting area, or in areas
posted: “Turn off two-way radio.” Obey all signs and
instructions.
Use only Motorola Solutions approved batteries.
Risk of explosion if the battery is replaced by an
incorrect type.
!
W A R N I N G
!
!
W A R N I N G
!
!
W A R N I N G
!
The European Union's WEEE directive requires that
products sold into EU countries must have the
crossed out trash bin label on the product (or the
package in some cases). As defined by the WEEE
directive, this cross-out trash bin label means that
customers and end-users in EU countries should not
dispose of electronic and electrical equipment or
accessories in household waste. Customers or end-
users in EU countries should contact their local
equipment supplier representative or service centre
for information about the waste collection system in
their country.
Supplier’s Declaration of Conformity
Per FCC CFR 47 Part 2 Section 2.1077(a)
Responsible Party
Name: Motorola Solutions, Inc.
Address: 2000 Progress Pkwy, Schaumburg, Il.
60196.
Phone Number: 1-800-927-2744
Hereby declares that the product:
Model Name: T482
conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d),
and section 15.109(a)
FCC Licensing Information
Control Buttons
MODE
Volume/Power
Push-to-Talk (High)
Mode Switch
Call Tone
Emergency
Button
Screen
Scan/Monitor
Menu/Lock
Flashlight LED
Accessory Port
Flashlight Button
Speaker
Microphone
Micro-USB
Charging Port
Push-to-Talk (Low)
Display Screen Guide
Numbers for Channel,
Call Tone
Numbers for Codes,
FM Radio Frequency
Battery Meter
Weather Alert
LockNoise Filtering
Scan
Call Tone
iVOX / VOX
Battery Save
Roger Tone
Keypad Tone
Power (high-low)
Status (transmit/
receive)
Quiet Charge
Modes
Getting Started
Talking and Listening
Menu Options
1 2 3 4 5 6
Specyfikacje produktu
| Marka: | Motorola |
| Kategoria: | radio |
| Model: | Talkabout T482 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Motorola Talkabout T482, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje radio Motorola
8 Grudnia 2024
8 Grudnia 2024
9 Października 2024
3 Października 2024
2 Października 2024
2 Października 2024
2 Października 2024
22 Września 2024
10 Września 2024
10 Września 2024
Instrukcje radio
- Peha
- BLUEPALM
- Scansonic
- REVO
- Lutron
- Hama
- MT Logic
- Delta
- Oregon Scientific
- DAP-Audio
- Nordmende
- Hyundai
- Kathrein
- OneConcept
- JL Audio
Najnowsze instrukcje dla radio
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
29 Marca 2025
26 Marca 2025
24 Marca 2025
14 Marca 2025
11 Marca 2025