Instrukcja obsługi Moxa NPort 5430I
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Moxa NPort 5430I (4 stron) w kategorii serwer. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/4
P/N: 1802054000312
NPort 5400 Series Quick
Installation Guide
Sixth Edition, January 2011
1. Overview
Welcome to Moxa NPort 5400, a 4 port communication device that
allows you to control RS-232 (for NPort 5410), RS-422/485 (for
NPort 5430/5430I) or RS-232/422/485 (for NPort 5450/5450I)
serial devices over a TCP/IP based Ethernet. Besides, NPort
5450-T and NPort 5450I-T are designed to use in wide
temperature environment.
NPort 5400 Series is a Moxa Green Product. Moxa’s Green Products
satisfy the RoHS directive of the European Parliament, and
accordingly, do not contain cadmium and cadmium compounds,
hexavalent chromium compounds, lead and lead compounds,
mercury and mercury compounds, PBBs (polybrominated
biphenyls), or PBDEs (polybrominated diphenyl ethers).
2. Package Checklist
Before installing NPort 5400, verify that the package contains the
following items:
• 1 NPort 5400 4-port Serial Device Server
• Power Adaptor (NPort 5450-T and 5450I-T do not include this
accessory)
• Power jack to 3-pin terminal block adaptor
• Wall mount kit
• Documentation and software CD
• Quick Installation Guide
• Warranty card
Optional Accessories
• DK-35A For 35 mm DIN-Rail; includes 4 screws
Notify your sales representative if any of the above items is missing or
damaged.
3. Hardware Introduction
As shown in the following figures, NPort 5410 has 4 Male DB9 ports,
for the RS-232 interface, NPort 5430/5430I has 4 5-pin terminal
blocks, for the RS-422/485 interface, and NPort 5450/5450I has 4
Male DB9 ports, for the RS-232/422/485 interface.
NPort 5410/5450/5450I
RJ45 10/100 Mbps Ethernet port
Power Jack Power Input
Terminal Block power input
RESET
LCM display panelIndicator LEDs Input buttons
Male DB9 serial port
Serial Device Server
5410
NP5 4 1 0 _61405
192 . 1 6 8.127.254
LAN V+ V-
Port 1
RS-422/785
Port 2
RS-422/785
Port 3
RS-422/785
Port 4
RS-422/785
NPort 5430/5430I
RJ45 10/100 Mbps Ethernet port
Terminal Block power input
RESET
LC
Power Jack Power Input
M display panelIndicator LEDs Input buttons
Serial Device Server
5430
NP 5410_61405
192.168.127.254
LAN V+ V-
RS-422/485 Terminal Block
T+ T- R+
D+
R-
D-
GND T+ T- R+
D+
R-
D-
GND T+ T- R+
D+
R-
D-
GND T+ T- R+
D+
R-
D-
GND
Port 1
RS-422/785
Port 2
RS-422/785
Port 3
RS-422/785
Port 4
RS-422/785
NPort 5450-T/5450I-T
RJ45 10/100 Mbps Ethernet port
Terminal Block power input
RESET
Indicator LEDs
Power Jack Power Input
Male DB9 serial port
Serial Device Server
5450
LAN V+ V-
Port 1
RS-422/785
Port 2
RS-422/785
Port 3
RS-422/785
Port 4
RS-422/785
Reset Button—Press the Reset button continuously for 5 sec to
load factory defaults: Use a pointed object, such as a straightened
paper clip or toothpick, to press the reset button. This will cause
the Ready LED to blink on and off. The factory defaults will be
loaded once the Ready LED stops blinking (after about 5 seconds).
At this point, you should release the reset button.
LED Indicators—NPort 5400’s top panel contains six LED
indicators, as described in the following table.
LED
Name
LED Color
LED Function
red Steady on: Power is on and NPort is
booting up.
Blinking: Indicates an IP conflict, or
DHCP or BOOTP server did not respond
properly.
green Steady on: Power is on and NPort is
functioning normally.
Blinking: The NPort has been located
by NPort Administrator’s Location function
Ready
off Power is off, or power error condition
exists.
orange 10 Mbps Ethernet connection.
green 100 Mbps Ethernet connection.
Ethernet
off Ethernet cable is disconnected, or has a
short.
orange Serial port is receiving data.
green Serial port is transmitting data.
P1, P2,
P3, P4
off No data is being transmitted or received
through the serial port.
LCM Display Panel (not support in -T model)—When the NPort
5400 unit is powered up, you will a see a display similar to:
N
P 5
4
1
0
_
6
1
4
0 5
1 9 2
. 1
6
8
. 1
2
7 . 2 5 4
This is where NP5410_61405 is the server’s name, and
192.168.127.254 is the server’s IP address.
LCM Panel Operation (not support in -T model)—There are
four buttons on NPort 5400’s top panel used to operate the
server’s LCM panel. Going from left to right, the buttons are:
Button Action
MENU Activates the main menu, or returns to a lower level.
＾ Scrolls up through a list of items shown on the LCM
panel’s second line.
﹀ Scrolls down through a list of items shown on the LCM
panel’s second line.
SEL Selects the option listed on the LCM panel’s second
line.
Detailed LCM Panel Operating instructions can be found on the
CD-ROM in the “NPort 5400 Series User’s Manual.”
– 1 – – 2 – – 3 –
Specyfikacje produktu
| Marka: | Moxa |
| Kategoria: | serwer |
| Model: | NPort 5430I |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Moxa NPort 5430I, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje serwer Moxa
2 Marca 2025
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
24 Września 2024
Instrukcje serwer
- Toshiba
- Digitus
- Raritan
- Provision ISR
- Supermicro
- Sun
- QNAP
- IStarUSA
- Black Box
- C2G
- Eaton
- MvixUSA
- Netgear
- Blackmagic Design
- StarTech.com
Najnowsze instrukcje dla serwer
9 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
28 Marca 2025
28 Marca 2025
28 Marca 2025
10 Marca 2025
10 Marca 2025
10 Marca 2025