Instrukcja obsługi NAV-TV My Touch NTV-KIT616

NAV-TV Niesklasyfikowane My Touch NTV-KIT616

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NAV-TV My Touch NTV-KIT616 (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

MY TOUCH VIM V2

VIM & CIM for select Ford vehicles with 8.4” My Touch

NTV-KIT 616

BHM

10 07/ /15

NTV-DOC 231

3950 NW 120th

Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760

BHM

10/07/15

NTV-DOC231

Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. :

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

2 | P a g e

Overview

The My Touch VIM V2 Kit enables viewing of DVD/IPOD video/AV input while in moon, as well as navigaon

desnaon input for select 2011+ Ford vehicles equipped with the 8.4” My Ford Touch media system.

Acvang Video in Moon/NAV Control in Moon is performed from wire trigger or factory dash buons for

select vehicles.

Kit Content

MY TOUCH VIM V2 Pinouts

Pin #

Descripon

Color

12v (+) Constant Power

Yellow

-- --Not Used (LIN)

White/Orange

-- --Not Used (LIN)

Orange

CAN ( ) HI (radio side) 125k

Green

CAN (125k) HI (vehicle side)

G ray

CAN (500k) HI (radio side )

Purple/Black

CAN (500k) HI (vehicle side)

White/Black

DIFF VID (radio side)

White/Blue

DIFF VID (vehicle side)

White/Orange

Ground (-)

Black

-- --Not Used

Blue

INPUT 1 (+) VIM Acvaon

Red

CAN (125k) LO (radio side)

Green/Black

CAN (125k) LO (vehicle side)

Gray/Black

CAN (500k) LO (radio side)

Purple

CAN (500k) LO (vehicle side)

White

DIFF VID (radio side)

Blue

DIFF VID (vehicle side)

Orange

VIM V2 Module

NTV-ASY232

Plug & Play T-Harness

NTV-HAR 266

USB Cable (updates)

NTV-CAB009

Wire Side View

Any wires not menoned here are not used

for this install.

BHM

10/07/15

NTV-DOC231

Agreement End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of its product. :

If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road use and passenger

entertainment only.

3 | P a g e

Installaon with radio removal (Edge)

1. Using a plasc pry tool, gently pry up side trim panel that run the length of

the radio bezel and center console.

2. Once removed, there will be t20 Torx screws holding the shier plate and

radio bezel in place. Remove these screws.

3. Place the vehicle in Drive or lower. Pry up the shift plate and move back.

4. With the shi plate moved the radio bezel will easily come out. Disconnect all

wiring aached to the bezel.

5. Remove the (4x) 7mm screws holding the screen in place.

6. Disconnect all wiring and set the screen aside.