Instrukcja obsługi NuTone CP2MZSN
NuTone
dzwonek do drzwi
CP2MZSN
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NuTone CP2MZSN (4 stron) w kategorii dzwonek do drzwi. Ta instrukcja była pomocna dla 23 osób i została oceniona przez 12 użytkowników na średnio 4.8 gwiazdek
Strona 1/4
1
WIRED / WIRELESS
DOOR CHIME
PUSHBUTTON
To register this product, visit: www.nutone.com
THIS PACKAGE INCLUDES:
n Cast Metal Escutcheon
n Wired Pushbutton
n Wireless Pushbutton and Battery
n Mounting Hardware
WIRED PUSHBUTTON INSTALLATION
WARNING
•
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING:
•
Use this unit only in the manner intended by the manufacturer. If you
have questions, contact the manufacturer at the address or telephone
number listed in the warranty.
•
Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such
as a tag, to the service panel.
•
Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction codes and standards.
•
When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
•
Use NuTone
®
16 volt transformer with a minimum rating of 10 VA
(purchase separately).
•
When stapling wires to studs or joists, do not allow staples to cut
through wire insulation.
1. Select pushbutton location
and drill a straight and
level 3/4” (19 mm) hole, 1”
(25 mm) deep.
2. Make sure that push button
assembly (A) is inserted
fully into escutcheon (B).
(Figure 1) Install chime
and transformer wires to
pushbutton terminals.
3. Install escutcheon/
pushbutton assembly
into hole and secure with
hardware provided.
4. Restore power at service entrance and press pushbutton to sound
chime.
INSTALLATION & OPERATING INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
WIRELESS PUSHBUTTON
INSTALLATION
The wireless pushbutton (C) is compatible with NuTone wireless
chimes. (Purchase separately) Refer to installation instructions
provided with wireless chime.
1. Open battery cover (D)
by sliding it in direction
indicated by arrow.
(Figure 2)
2. Install battery (E) into
wireless pushbutton.
(Figure 3)
3. Remove wired pushbutton
mechanism from pushbutton /
escutcheon assembly by
turning pushbutton mechanism
counterclockwise and pulling it
out. (Figure 4)
4. Insert wireless
pushbutton
mechanism and
twist clockwise.
(Figure 5)
5. Test operation.
Hold wireless
pushbutton near
chime and press
pushbutton. If
chime does not
sound - see a.
through c. on
page 2.
FIGURE 1
B
A
FIGURE 4
1
2
FIGURE 5
1
2
FIGURE 2
FIGURE 3
C
D
E
+ -
Specyfikacje produktu
| Marka: | NuTone |
| Kategoria: | dzwonek do drzwi |
| Model: | CP2MZSN |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z NuTone CP2MZSN, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje dzwonek do drzwi NuTone
30 Marca 2025
30 Marca 2025
30 Marca 2025
30 Marca 2025
1 Października 2024
11 Września 2024
11 Września 2024
11 Września 2024
11 Września 2024
11 Września 2024
Instrukcje dzwonek do drzwi
- Bea-fon
- Techly
- ALC
- Pentatech
- Steren
- V-TAC
- Acti
- Intersteel
- Somfy
- EQ3
- Nest
- Heidemann
- Eufy
- SkyBell
- SilverCrest
Najnowsze instrukcje dla dzwonek do drzwi
7 Kwietnia 2025
12 Marca 2025
22 Lutego 2025
20 Lutego 2025
19 Lutego 2025
4 Lutego 2025
4 Lutego 2025
9 Stycznia 2025
8 Stycznia 2025
1 Stycznia 2025