Instrukcja obsługi NUVO Beacon 60/6827
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla NUVO Beacon 60/6827 (2 stron) w kategorii Lampa. Ta instrukcja była pomocna dla 23 osób i została oceniona przez 12 użytkowników na średnio 4.7 gwiazdek
Strona 1/2
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING
ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR THE CIRCUIT BREAKER
IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow the steps
in the order given. Under no circumstances should a xture be hung on house
electrical wires, nor should a swag type xture be installed on a ceiling which
contains a radiant type heating system. Read instructions carefully. If you are
unclear as to how to proceed, consult a qualied electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts are included
as shown in gure. Be careful not to misplace any of the screws or parts, which
are needed to install this xture.
STEP 1: Thread rod (D) into the coupling. Carefully pass the wires through each
rod during assembly. Repeat step 1 with rods (A), (B) and (C) until the desired
hanging height is reached.
STEP 2: Rotate the arms to the right direction.
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
STEP 1: Secure the two screws to the mounting plate. You should leave the proper
length of the two screws beyond the surface of the mounting plate to ensure
enough thread is available to properly mount the canopy with the
mounting screws.
STEP 2: Pull the existing electrical wires out of the junction box and make proper
connections using wire nuts.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised dimples
on the mounting bar. Wrap the ground wire from the xture (if supplied) around
the green grounding screw, then connect it to ground wire from the outlet box
(if not xed on the outlet box) using a wire connector (not supplied). If ground wire
from the xture is not supplied, wrap the ground wire (if not xed on the outlet
box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify which
group your xture wire(s) falls into and connect the wires according to the
directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is square
shaped or ridged and the less tracer wire is round in shape or smooth (seen
best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly against the
black wire from the outlet box. Do NOT twist wires together before using wire
connectors.
STEP 4: Fit a wire connector over the wires and screw the connector clockwise
until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps 3 and 4 as above, and check again for a
rm connection.
STEP 6: Connect the xture wire from group B to the white wire from the outlet
box in the same manner. Make sure no bare wires can be seen outside wire
connectors.
FINAL ASSEMBLY
STEP 1: Position canopy over mounting plate and align holes in canopy with
mounting screws. With thread protruding through canopy surface, thread and
secure three screws.
STEP 2: Install lamp (not supplied). Please do not exceed the maximum capacity
recommended on the socket.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap. Do not use
abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement
parts. Be sure to use exact wording from illustration when ordering parts.
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
INSTALLATION AND SAFETY INSTRUCTIONS
ITEM NO: 60-6827
ARTÍCULO Nº: 60-6827
ARTICLE N°: 60-6827
Junction Box
Wire Nuts
Screws
Canopy
Rod (A)
Rod (B)
Rod (C)
Rod (D)
Coupling
Mounting Screws
Mounting Plate
FIGURE
Specyfikacje produktu
| Marka: | NUVO |
| Kategoria: | Lampa |
| Model: | Beacon 60/6827 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z NUVO Beacon 60/6827, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Lampa NUVO
4 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
9 Października 2024
9 Października 2024
Instrukcje Lampa
- Näve
- Nordride
- Kartell
- Royal Sovereign
- DPM
- ARRI
- Flex
- InFocus
- Carson
- Currey & Company
- Trust
- Nicols
- Adviti
- Artemide
- Lirio By Philips
Najnowsze instrukcje dla Lampa
8 Kwietnia 2025
8 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025