Instrukcja obsługi PAC AP4-TY14
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla PAC AP4-TY14 (5 stron) w kategorii odbiornik. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 3.8 gwiazdek
Strona 1/5
© 2024 Stinger Solutions
C
Page 1
Rev: 1
Date:09242024
Advanced Amplier Interface
for Select Toyota Applications
AP4-TY14
The AP4-TY14 provides a 6-channel pre-amp output for use with aftermarket audio equipment. Using the full range
xed level head unit output, in conjunction with data bus messages, the AP4-TY14 delivers a variable 5v RMS pre-
amp output with fading, balance, equalization, and level control capabilities. The module also retains audio from
other vehicle features such as factory navigation prompts, Bluetooth and Voice Activation. An accessory controlled
remote amplier turn on wire is also provided by the AP4-TY14. When used in conjunction with the APA-TOS1 (sold
separately), the module can provide a variable 2-channel ber optic digital audio output (TOSLINK).
Introduction and Features
Important Notes
1. Toyota Safety Connect (SOS) can easily be retained. See the page 3 for detailed instructions.
2. The aftermarket amplier must have a very solid ground and the amplier power/ground connections should be made
before connecting the RCA's or Remote on the AP4-TY14.
3. The factory radio's speed controlled volume, DSP, and surround sound mode are not supported by the AP4 outputs.
4. The factory amplier must remain connected and in the vehicle after the AmpPRO has been installed.
5. Prior to testing, cycle the ignition off and back on again to properly initialize the AP4-TY14.
6. The radio's beep setting must be enabled on the factory radio in order to hear the audible tones when making selections
through the radio.
7. Initially, if the beep through the AP4-TY14 does not match the on/off selection through the radio, cycle the beep to the
opposite setting and back, then test again.
8. The radio's beep volume and minimum volume levels are set to 0 dB by default. If you are happy with this level in your
particular application, additional adjustment is not required. Please refer to the Setup and Conguration section on page 4
for more details.
9. The Radio's Nav / VR Voice, incoming E-mail tone, Ringtone, In-Call, Incoming SMS / MMS tone and Incoming SMS Voice
volumes can be adjusted through the radio's settings menu as they were prior to installation of the AP4-TY14.
10. The remote output is rated at 2A of current. If more current is needed, an external relay must be used.
11. Channels 5 and 6 are non-fading outputs. The output level of channels 5 and 6 can be controlled using the supplied level
control knob.
Wiring Connection Chart
To Aftermarket
Amplier
Non-FadingRearFront
1(L) 2(R) 4(R) 5(L) 6(R)3(L)
Non-Fading
Level Control
Knob
Remote Turn On Output (2A Max)
SOS Mute ( - Trigger Input )
GRAY
GRAY
BLACK
BLACK
WHITE
WHITE
28-pin
10-pin
30-pin
Specyfikacje produktu
| Marka: | PAC |
| Kategoria: | odbiornik |
| Model: | AP4-TY14 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z PAC AP4-TY14, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje odbiornik PAC
12 Lutego 2025
12 Lutego 2025
12 Września 2024
Instrukcje odbiornik
- Vimar
- RME
- Bowers & Wilkins
- Vaddio
- Focal
- Canor
- Skytec
- Strong
- Teac
- Tangent
- Naim
- Accell
- Dreambox
- Gold Note
- Proel
Najnowsze instrukcje dla odbiornik
9 Kwietnia 2025
9 Kwietnia 2025
5 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
30 Marca 2025
30 Marca 2025