Instrukcja obsługi Pioneer gm 3000
Pioneer
Radia samochodowe
gm 3000
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pioneer gm 3000 (74 stron) w kategorii Radia samochodowe. Ta instrukcja była pomocna dla 25 osób i została oceniona przez 13 użytkowników na średnio 4.3 gwiazdek
Strona 1/74
ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS
BRIDGEABLE POWER AMPLIFIER
AMPLIFICATEUR DE PUISSANCE PONTABLE
Owner’s Manual
GM-3000T
Mode d’emploi
1
Contents
Before Using This Product ...................... 2
In case of trouble .............................................. 2
WARNING ........................................................ 2
Setting the Unit .......................................... 3
Gain Control ...................................................... 3
Power Indicator ................................................ 4
BFC (Beat Frequency Control) Switch ............ 4
LPF (Low-Pass Filter) Select Switch ................ 4
Connecting the Unit .................................. 5
Connection Diagram ........................................ 6
Connecting the Power Terminal ........................ 7
Connecting the Speaker Output Terminals ...... 7
Using the Speaker Input .................................... 8
Connecting the Speaker wires .......................... 9
Installation ................................................ 10
Example of installation on the floor mat
or on the chassis ...................................... 10
Specifications .......................................... 11
Before Using This Product
2
ENGLISH ESPAÑOL DEUTSCH FRANÇAIS ITALIANO NEDERLANDS
Thank you for purchasing this PIONEER
product. Before attempting operation, be
sure to read this manual.
In case of trouble
When the unit does not operate properly,
contact your dealer or the nearest autho-
rized PIONEER Service Station.
CAUTION
Never replace the fuse with one of greater
value or rating than the original fuse. Use
of an improper fuse could result in over-
heating and smoke and could cause dam-
age to the product and injury including
burns.
CAUTION
Do NOT install or use your Pioneer ampli-
fier by wiring speakers rated at 4 Ohm (or
lower) in parallel to achieve a 2 Ohm (or
lower) bridged mode (Diagram B).
Amplifier damage, smoke, and overheat-
ing could result from improper bridging.
The amplifier surface could also become
hot to the touch and minor burns could
result.
To properly install or use a bridged mode
for a two-channel amplifier and achieve a
4 Ωload, wire two 8 Ωspeakers in paral-
lel with Left + and Right - (Diagram A) or
use a single 4 Ωspeaker. For a four-chan-
nel amplifier, follow the speaker output
connection diagram for bridging as shown
on the back of your amplifier, and wire
two 8 Ωspeakers in parallel to achieve a 4
Ω Ωload or use a single 4 speaker per
channel.
If you have any questions or concerns,
please contact your local authorized
Pioneer dealer or call Pioneer customer
service.
WARNING
• Always use the special red battery and ground
wire [RD-223], which is sold separately. Connect
the battery wire directly to the car battery positive
terminal (+) and the ground wire to the car body.
• Do not touch the amplifier with wet hands.
Otherwise you may get an electric shock. Also,
do not touch the amplifier when it is wet.
• For traffic safety and to maintain safe driving
conditions, keep the volume low enough so that
you can still hear normal traffic sound.
• Check the connections of the power supply and
speakers if the fuse of the separately sold battery
wire or the amplifier fuse blows. Detect the cause
and solve the problem, then replace the fuse with
another one of the same size and rating.
• To prevent malfunction of the amplifier and
speakers, the protective circuit will cut the power
supply to the amplifier (sound will stop) when an
abnormal condition occurs. In such a case, switch
the power to the system OFF and check the
connection of the power supply and speakers.
Detect the cause and solve the problem.
• Contact the dealer if you cannot detect the cause.
• To prevent an electric shock or short-circuit
during connection and installation, be sure to
disconnect the negative (–) terminal of the battery
beforehand.
• Confirm that no parts are behind the panel when
drilling a hole for installation of the amplifier. Be
sure to protect all cables and important equipment
such as fuel lines, brake lines and the electrical
wiring from damage.
Diagram A - Proper
8
Ohm
Speaker
+ -
8
Ohm
Speaker
Pioneer
Amplifier
4 Ohm Bridged Mode
+
L+ R-
-
Diagram B - Improper
4
Ohm
Speaker
+ -
4
Ohm
Speaker
Pioneer
Amplifier
2 Ohm Bridged Mode
+
L+ R-
-
Specyfikacje produktu
| Marka: | Pioneer |
| Kategoria: | Radia samochodowe |
| Model: | gm 3000 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Pioneer gm 3000, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Radia samochodowe Pioneer
5 Stycznia 2025
3 Stycznia 2025
7 Grudnia 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
Instrukcje Radia samochodowe
- Radia samochodowe Nedis
- Radia samochodowe Smart
- Radia samochodowe Mercedes-Benz
- Radia samochodowe Hifonics
- Radia samochodowe Shuttle
- Radia samochodowe Medion
- Radia samochodowe Voxx
- Radia samochodowe Lanzar
- Radia samochodowe Norauto
- Radia samochodowe Multilaser
- Radia samochodowe Tokai
- Radia samochodowe AEG
- Radia samochodowe Rodek
- Radia samochodowe Audio-Technica
- Radia samochodowe VDO Dayton
Najnowsze instrukcje dla Radia samochodowe
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
15 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
14 Stycznia 2025
13 Stycznia 2025