Instrukcja obsługi Pulsar S108
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pulsar S108 (5 stron) w kategorii Nie skategoryzowane. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.9 gwiazdek
Strona 1/5
1
S108
v1.4
S -ports switch for 8 IP cameras 108 10
Edition 6 z dnia 18.07.2019 :
: Supercedes the edition 5 from 04.02.2019 EN**
Features:
Switch 10 ports
8 PoE ports 10/100Mb/s (data and power supply)
2 ports Mb/s (UP LINK) 10/100
Long Range mode (up to 250m)
W for each PoE port, supports devices complaint 30
with the IEEE802.3af/at standard (PoE+)
Supports auto-learning and auto-aging of MAC
addresses (1K size)
The PSD V DC/2,3 A/120 W max. 520230
power supply desktop type included
Additional assembly elements
LED indication
warranty 2 year from the production date –
Example of use.
1. Technical description
1.1. General description.
S108 is a 10-ports PoE switch designed to supply IP cameras operating in IEEE 802.3af/at standard.
Automatic detection of any devices powered in the PoE/PoE+ standard is enabled at the 1 8 ports of the switch. The UP LINK –
ports is used for connection of another network device via RJ45 connector The LEDs at the front panel indicate the operation .
status (description in the table below).
The PoE technology ensures a network connection and reduces installation costs by eliminating the need to supply a
separate power cable for each device. This method allows supplying other network devices, such as IP phone, wireless access
point or router.
2
1.2 Block diagram.
Fig. 1. Block diagram.
1.3 Description of components and connectors.
Table 1. (See Fig . 2)
Component No.
( . 2) Fig
Description
[1]
8 x PoE ports (1 ) ÷8
[2]
2 x UP LINK port
[3]
Power Socket of the DC
[4]
Additional assembly elements
[5]
Switch of mode Long Range
Fig. 2. . The view of the switch
3
1.4 Technical parameters
Table 2 .
Ports
10 ports 10/100Mb/s (8 x PoE + 2 x UP LINK)
with connection speed auto-negotiation and MDI/MDIX Auto Cross)
PoE power supply
IEEE 802. 3af/at 8 ports), 52 V DC / 30 W at each port * (1÷
Long Range mode
Long Range, VLAN
Protocols, Standards
IEEE802.3, 802.3u, 802.3x CSMA/CD, TCP/IP
Bandwidth
1,6Gbps
Transmission method
Store-and-Forward
Optical indication of
operation
Switch power supply;
Link/Act;
PoE Status
Power supply
~100 ÷ 240 V; 50/60 Hz;1,3 A
the PSD 520230 52 V DC/2,3 A/120 W max. power supply desktop type
Operating conditions
temperature - 10°C ÷ 40°C,
relative humidity - no condensation 5% 90%,
Dimensions
W=190, H=28, D=105 [+/- 2mm]
Additional equipment
plate to be xed surface
Gross/Net weight
1,2 / 1,4 kg
Protection class
EN 60950-1:20 07
II (second)
Storage temperature
- 20°C ÷ 60°C
Declarations
CE
* The given value of 30 W per port is the maximum value. The total power consumption should not exceed 96 W.
2. Installation
Requirements 2.1.
The unit should be mounted in conned spaces, in accordance with the 2nd environmental class, with normal relative
humidity (RH=90% maximum, without condensation) and temperature from -10°C to +40°C. Ensure the free flow of air around
the unit. The PSU shall work in a vertical position that guarantees suicient convectional air-ow through ventilating holes of the
enclosure.
The switch load balance should be done before installation. The given value of 30 W per port is the maximum value
referring to a single output. The total power consumption should not exceed 96 W. The increased demand for power is
particularly evident in the case of cameras with heaters or infrared illuminators - when launching these features, the power
consumption increases rapidly, which may adversely aect the operation of the switch. As the device is designed for a
continuous operation and is not equipped with a power-switch, therefore an appropriate overload protection in the power supply
circuit should be provided. The electrical system shall be made in accordance with applicable standards and regulations.
2.2. Long Range mode
Switch enables operation in two modes: standard and extended range. When the Long Range switch is in
STANDARD position (see Fig. 5), PoE ports operate at 100 Mb / s up to 100 meters. After switching to EXTEND position,
range is increased to 250 meters and speed is reduced to 10 Mb / s. Additionally, VLAN function, which isolates the PoE
ports between each other (communication takes place between the UpLink ports and individual PoE), is activated. In both
modes, the UpLink port speed is 100 Mb / s.
Note: Changing the modes requires a power restart!
Specyfikacje produktu
| Marka: | Pulsar |
| Kategoria: | Nie skategoryzowane |
| Model: | S108 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Pulsar S108, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Nie skategoryzowane Pulsar
7 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
11 Marca 2025
11 Marca 2025
11 Marca 2025
11 Marca 2025
11 Marca 2025
11 Marca 2025
11 Marca 2025
Instrukcje Nie skategoryzowane
- Nie skategoryzowane Gembird
- Nie skategoryzowane Fischer
- Nie skategoryzowane Corbero
- Nie skategoryzowane Neumann
- Nie skategoryzowane Kica
- Nie skategoryzowane Phoenix Gold
- Nie skategoryzowane IMG Stageline
- Nie skategoryzowane Taga Harmony
- Nie skategoryzowane Macally
- Nie skategoryzowane American DJ
- Nie skategoryzowane Conair
- Nie skategoryzowane NightStick
- Nie skategoryzowane Magewell
- Nie skategoryzowane Electrolux
- Nie skategoryzowane Expobar
Najnowsze instrukcje dla Nie skategoryzowane
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025
9 Kwietnia 2025