Instrukcja obsługi Pyle PB-KCM3W

Pyle SmartWatch PB-KCM3W

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PB-KCM3W (1 stron) w kategorii SmartWatch. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 7.5 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

A cyclist symbol appears to the left of the

speed. The wheel turns forward to

indicate acceleration. The wheel turns

backward to indicate deceleration.

TRIPMETER (DST)

(Trip Information Reset Mode)

It is used to remind you for the parts replacement or to lubricate

the chains and wheels after the peset distance is reached.

Right after KM/ MILE selection, the preset total distance of

600km (or miles) will ash, press the RIGHT button to select

between 200, 400, 600 & 800km (or miles) and press LEFT

button to conrm.

For example, if 600 km is selected, the spanner ( ) will ash

whenever the total distance (ODO) reach 600, 1200, 1800km

(or miles).

Press the LEFT button to stop ashing of spanner( ).

START / STOP

Art No.: BC-P3-GB

FUNCTIONS

ATTENTION: Computer Functions refer to the packing details.

FEATURES

MAINTENANCE PROGRAM

CLOCK (12H / 24H)

MAXIMUM SPEED (MXS)

AVERAGE SPEED (AVS)

TRIP TIMER (TM)

TEMPERATURE

ODOMETER SAVE FUNCTION

MALFUNCTION PROBLEM

SCAN

FREEZE FRAME MEMORY

ODOMETER (ODO)

SPEED COMPARATOR (Cadence)

SPEED TENDENCY (Acceleration & Deceleration)

SPEEDOMETER (SPD)

WHEEL SIZE INPUT

KM / MILE SELECTION

4 5 7 9 13 16

Speedometer (SPD)

- 0~99.9 KM/hr or M/hr

Tripmeter (DST)

- 0~999.9 KM or M

Odometer (ODO)

- 0~9999.9 KM or M

Auto Trip Timer (TM)

- 9: 59’ 59”

Maximum Speed (MXS)

- 0~99.9 KM/hr or M/hr

Average Speed (AVS)

- 0~99.9 KM/hr or M/hr

Scan

- for DST, MXS, AVS, TM

Freeze Frame Memory

- for TM, AVS, DST

Speed Comparator

- (+ or -)

Speed Tendency or

Digital Clock

12 / 24 hour selectable

Temperature

(-10°C to +50°C)

°C / °F Selection

Odometer Save Function

Maintenance Program

INSTRUCTION MANUAL

CYCLE COMPUTER

Fig. 2

COMPUTER

EL BACKLIGHT (OPTIONAL)

*EL BACKLIGHT (OPTIONAL)

Slide the computer onto the mounting bracket until it snaps

rmly into position. Press the release button to take out the

computer as shown in Fig. 1.

After the wheel size input, the following function is selection of

kilometers or miles as the measurement for distance. Press the

RIGHT button to choose between kilometer (KM) and Mile (M),

press the LEFT button to conrm.

To start the unit, press the RIGHT button to turn on the display

and the wireless mounting system. To stop the unit, left unused

for over 5-6 minutes and then the computer will automatically

switch o to preserve batteries.

A “+” or “-” sign appears to the right of the

speed. “+” indicates you are travelling

faster than your average speed (AVS). A

“-” indicates you are riding slower than your

average speed.

Total distance travelled is indicated by

ODO and display on the bottom line. To

reset ODO, press and hold LEFT and

RIGHT buttons for 2 seconds or remove

the battery. Press the RIGHT button to

enter DST mode.

Trip distance measurement is indicated by

DST and is displayed on the bottom line.

Tripmeter is activated automatically with

speedometer input. Reset DST to zero by

pressing the LEFT button for 2 seconds;

DST (Trip distance), TM (Trip Timer) & AVS

(Average Speed) will also be reset at that

time. Press the RIGHT button to enter

MXS mode.

Maximum speed measurement is indicated

by MXS and is displayed on the bottom

line. Maximum speed is stored in memory

and updated only when a higher speed is

reached. To reset MXS, press and hold the

RIGHT button to enter AVS mode.

Press and hold LEFT button for 2 seconds,

” °C ” will start to ash. Press RIGHT

button to select “ °C” or “ °F” and press

LEFT button to conrm.

Press RIGHT button to enter the Scan

mode.

The EL backlight can be turned on either as follows:

1) Holding the RIGHT button for 2 seconds, the EL light will be

turned on for 8 seconds and the computer will then go to fast

scan mode with trip distance, maximum speed, average

speed and trip timer displayed once.

2) Press once on the LEFT Button, the EL light will be turned

on for 4 seconds and the comuter will go to the freeze frame

menory mode as well.

Inaccurate maximum

speed reading

No speedometer

reading

Slow display

response

Black display

No trip distance

reading alignment

Display shows

irregular gures

Unknown atmospheric or RF

interference

Improper magnet/transmitter

alignment

Check battery and correct

installation

Temperature outside of operating

limits (0-55 °C)

Temperature too hot, or display

exposed to direct sunlight too long

Check correct transmitter / magnet

Check battery and correct

installation

Take out computer battery and

install again

The Scan mode allows DST, MXS, AVS

and TM to cycle on the screen without

pressing any keys. Press the RIGHT

button to enter the Clock mode.

Press the LEFT button, Freeze Frame

Memory can lock the display at the end of a

ride segment and information TM, DST and

AVS which will be ashing, can be read at a

later time by pressing the RIGHT button.

To release the memory, press the LEFT

button until the display digit is static again.

This is particularly useful when crossing

the nish line of a time trial, since the TM

cannot be stopped manually.

The SAVE function allows you to keep the

important data of total distance (ODO)

even after replacement of battery.

To set ODO, after battery replacement and

wheel size setting, press RIGHT button to

ODO mode and then press and hold LEFT

button for 2 seconds until the last digit

ickering. To adjust number, press the

RIGHT button. Press the LEFT button to

conrm. Repeat above sequence to reach

the desired odometer value. Press the

LEFT button again to return to normal ODO

mode.

Average Speed measurment is indicated

by AVS and is displayed on the bottom line.

AVS is calculated with the Trip Timer (TM),

so AVS is the average speed only while

riding. Press the RIGHT button to enter TM

mode.

Trip timer measurement is indicated by TM

and is displayed on the bottom line. Trip

Timer is activated automatically with

speedometer input [On when you ride and

o when you stop.] It records only the time

spent actually riding.

Reset TM to zero by pressing the LEFT

button for 2 seconds in DST mode. Press

the RIGHT button to enter Temperature

mode.

A 12 or 24-hour digital clock is indicated by

the ickering colon on the bottom line. To

switch between the 12 and 24 hour format

or to adjust time, press the LEFT button for

2 seconds. “24H” will start to icker. Use

the RIGHT button to select “12H” for12-

hour format or “24H” for 24-hour format.

Press the LEFT button to conrm. Next the

hour digits will start to icker. Use the

RIGHT button to select the hour. To change

minutes, press LEFT button again. The

minutes will start to icker. Use the RIGHT

button to select the minutes. Press the

LEFT button once more to return to

CLOCK Mode. Press the RIGHT button to

enter ODO mode.

Instantaneous Speed is indicated on the

top line. The range of measurement is

from 0 to 99 KM/ hr [0 to 99 M/ hr] and

accuracy is ± 0.5 KM/ hr [M/ hr].

Press and hold LEFT and RIGHT buttons for 2 seconds or after

the replacement of battery, the unit is switched to wheel size

input mode. Multiply wheel diameter, d (Fig. 2) in millimeters by

3.1416 to determine wheel factor, c.

Press the LEFT button to select digit to be input and the RIGHT

button to adjust the digit to the desired number (hold for fast

advance). Press the LEFT button again to KM/MILE selection.

(Note: removing battery will erase Wheel Size Input)

distance in millimeter

per one turn

For convenience you can refer to the chart of wheel diameter

size factor inputs.

ATTENTION !! Refer to the appendix for installation reference.

Release

Fig. 1

Specyfikacje produktu

Marka:	Pyle
Kategoria:	SmartWatch
Model:	PB-KCM3W
Kolor produktu:	Biały
Typ kontroli:	obrotowy
Wbudowany wyświetlacz:	Tak
Typ wyświetlacza:	LCD
Położenie urządzenia:	Wolnostojący
Wysokość produktu:	850 mm
Szerokość produktu:	600 mm
Głębokość produktu:	523 mm
Waga produktu:	46000 g
System suszenia:	Pompa grzewcza
Poziom hałasu:	64 dB
Opóźniony start czasomierza:	Tak
Opóźniony start:	24 h
Czas cyklu:	209 min
Klasa wydajności energetycznej:	A+++
Skala efektywności energetycznej:	A +++ do D
Wskaźnik pozostałego czasu:	Tak
Zabezpieczenie przed dziećmi:	Tak
Typ ładowania:	Od przodu
Zawias drzwiczek:	Prawy
Pojemność znamionowa:	8 kg
Roczne zużycie energii:	177 kWh
Kategoria suszenia:	A
Ilość programów suszących:	16
Źródło ciepła:	Prąd elektryczny
Zużycie energii:	1.43 kWh
Funkcja Anti-Crease:	Tak
Oświetlenie wnętrza bębna:	Tak
Wskaźnik poziomu wody:	Tak
Wskaźnik czyszenia filtra:	Tak