Instrukcja obsługi Pyle PMA82

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PMA82 (1 stron) w kategorii Miernik wiatru. Ta instrukcja była pomocna dla 22 osób i została oceniona przez 2 użytkowników na średnio 4.1 gwiazdek

PMA82to measure aitemperature r

PMA82 Anemometer.T PMA82 Anemometer Congratulations on your purchase of the he

1

Introduction

measures air velocity in five uni of measure: feet per minute (ft/min), meters pesec tsr

-ond (m/sec), miles per hour (MPH), kilometers per hour (km/hr),& nauticalmilespehour r

(knots)&CFM(ft /min). An internal sensor allows

or Fahrenheit units.

This meter is

service.

Meter Description

1. Vane sensor

2. LCD display

3. Units/°F/°C key

4.MaMin x/ key

5. Hold key

Note: Battery compartment is on rear of unit

MAX MIN

V EL

�

�

123

4

5

6

7

Display

1. MAX MIN Record mode

2. Temperature display

3. Temperature units

4.Velocitunits y

5. MAX or MIN mode

6.Velocitdispl y ay

7. Low battery indicator

CFM

provide years of reliable

shipped fully tested and calibrated

and withproper

6. On/Off Key

3

PMA82

INSTRUCTION MANUAL

UNITS

MAX

MIN

1

5

43

6

2

shuts off after 15 minutes to conserve battey energy.

2

Operation

Meter Power

1. Press the PER buon to turn the meter on. the display does not switch on, check OWttIf

that a fresh 9V baery is installed. tt

2. Press the POWER button to turn the meter off.

3. The meter is equipped with an AUTO POWER OFF feature. The meter automatically

Measuring Air Velocity and Temperature

1. Place the sensor in the air stream under test.

2. Read the Air Velocity and Temrature measurements directly on the LCD. pe

3. To calculate Air Volume in CFM (cubic feet per minute) or CMM (cubic meters per

minute) refer to the ‘Useful Equations and Conversions’ section.

Selecting the Temperature unit of measure (

oC/oF)

Press and hold the UNITS key for 3 seconds to select the temperature unit of measure.

The meter will beep twice and the display will indicate the currently selected unit of

measure.

Selecting the Air Velocity unit of measure

Press the UNITS key to change the unit of measure for Air Velocity measurements. The

displaillflect the cuent selection.sttsy w re rr A li of measurement uni is printed in the

specificaions lain thismanual.t ter

Record and Recall MAX / Min Function

1. To begin capturing the Maximum (MAX) and Minimum (MIN) air velocity and

temperature readings, press the MAX/MIN key and the ‘RECORD’ icon will appear in

thedispla y.

2. Now, use the MAX/MIN key to toggle the view from MIN to MAX to RECORD. The

‘MAX’ or ‘MIN’ will appear along with the recalled reading for convenience. In RECO RD

mode, the meter will display the cuent reading but will continue to capture a rrMAXnd

MIN readings.

3. To return to normal operation, press and hold the MAX/MIN key for 3 seconds to clear

and stop M/MIN recording. The meter will beep twice and the ‘M’/‘MIN’ and AXAX

‘RECRD’ iconsillitch off.O w sw

Area Set for CFM

-Turn off the meter

-Press the HOLD key and hold

-While holding the HOLD key turn on the meter.It will now be in area set mode

“set area” will display.The area range can be set from 0 to 999.9ft

-Press the MAX/MIN key to shift the radix point(decimal point).

-Press the HOLD key to shift between flashing digits

-Press the UNITS key to change the value of the flashing digit

-After setting the area for CFM(inputting the square footage of the duct0,the

operator must turn the meter off,then turn the meter on again.At this point,

the meter will be set to read CFM for the desired area.

2

knots (nautical miles per hour) 1.94 - 48.5 knots 0.1 knots ± (3% + 0.4 knots)

mph (miles per hour) 2.24 -56.0 mph 0.1 mph ± (3% + 0.4 mph)

km/h (kilometers per hour) 3.6 - 90.0 km/h 0.1 km/h ± (3% + 0.8 km/hr)

m/s (meters per second) 1.00 - 25.00 m/s 0.01 m/s ± (3% + 0.20 m/sec)

ft/min (feet per minute) 196 - 4900 ft/min 1 ft/min ± (3% + 40 ft/min)

Max. 80% RH

32 °F to 122 °F (0 °C to 50 °C)

Dual function 8888 count LCD display

3

Maintenance

Battery Replacement

When the battery power falls low, the low battery icon will appear on the LCD. Replace

the 9V battery by removing the Phillips screw on the battery compartment door and

aeing the baery compaen Ensure that the compartment cover is securely ccssttrtmt.

fastened when finished.

Cleaning and Storage

Wipe the meter and vane with a damp cloth as needed. Do not apply abrasive, solvents, or

other cleaners to the surface of the meter or vane. Store with the ttery removed and ba

avoid extreme temperature and humidity.

Specifications

Circuit description Custom LSI microprocessor design

Display

Measurement units m/s, km/h, min, knots , mph, Temperature: ft/oC/oF

Data hold Freezes reading on the display

Sensor Structure Air velocity senso Conventional twied vane arm with low-r:st

friction ball-bearing

Memory Recall Record and Recall Maximum/Minimum (MAX/MIN) readings

A Power off utoAfter 15 minutes with disable feature

Operating Temperature

Opating Humidity er

Power Supply 9V battery

Power Consumption Approx. 8.3mA DC

Air Velocity Range Specifications

Measurement Range Resolution Auracy cc

(% of reading)

Temperature Range Specifications

ycaruccA noituloseR egnaR

32oF to 122oF (0oC to 50oC) 0.1oF (0.1oC)± 4.0oF (2

oC)

CFM

Air Flow Range Specifications

Unit Range ResolutionArea

CFM(cubic feet per minute)0-999,900ft /min0.10.000-999.9ft

in Celsius

use will

Specyfikacje produktu