Instrukcja obsługi Pyle PMX802M
Pyle
Ręczny blender
PMX802M
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Pyle PMX802M (9 stron) w kategorii Ręczny blender. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.6 gwiazdek
Strona 1/9
Mul-Channel Mixers
PyleUSA.com
Warnings
Please be sure to read, keep and refer to instrucons listed in this manual.
Do not use this device near water or expose to moisture.
Clean only with a dry cloth.
Do not block any venlaon openings and allow adequate space for air ow during operaon.
Do not install near any heat sources or other devices that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug.
Protect the power cord from any kind of damage or corrosion.
Unplug the mixer when not in use or when unused for long periods of me.
Refer all service to qualied service personnel. Servicing is required when the mixer has been damaged or performs in an unusually.
Use only speaker cables when connecng speakers to amplier outputs. Using other types of cables is a re hazard.
Exposure to extremely high noise levels may cause in permanent hearing loss. Individuals vary considerably to noise induced hearing loss but
take precauon when listening at high levels.
If the power cord is damaged (i.e., cut or a bare wire is exposed), ask your dealer for a replacement. Using the unit with a damaged power cord
is a re and electrical shock hazard.
Should this unit be dropped or the cabinet be damaged, turn the power switch o, remove the power plug from the AC outlet, and contact your
dealer. If you connue using the unit without heeding this instrucon, re or electrical shock may result.
C A U T I O N
If the unit is damaged or non-operaonal, please nofy your dealer and the shipping company immediately. Claims for
damage or replacement may not be granted if not reported properly or in a mely manner.
Connect this unit’s power cord only to an AC outlet of the type stated in this Manual or as marked on the unit. Failure to do so may result in
re and/or electrical shock.
Do not place heavy objects on top of the power cord. A damaged power cord is also a re and electrical shock hazard.
Use only the included power cord for this unit, using other types may again result in re and electrical shock.
Do not set all equalizer controls and faders to maximum levels. Doing so may cause oscillaon depending on the condion of the connected
unit and speakers, and may also damage the speakers.
The performance of components on this mixer such switches, rotary controls, faders, and connectors, deteriorates over me. The rate as
depends on the operang environment and is somemes unavoidable. Consult your dealer about replacing defecve components.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT ATTEMPT TO OPEN OR ACCESS THE INSIDE OF
THE UNIT. REFER ALL SERVICING TO A QUALIFIED PYLE
SERVICE PERSONNEL.
This lightning ash symbol is intended to alert the user to the presence of uninsulated and “dangerous
voltage” within the mixer's enclosure that may be of sucient power to constute a risk of electric shock.
This exclamaon point symbol is intended to alert the user to the presence of important operang
and maintaining instrucons, that one should pay aenon to and keep for future reference.
Mul-Channel Mixers
PyleUSA.com
Installaon
Install the mixer on an even surface to allow for sucient airow and venlaon during use. The device is equipped with
electronically controlled cooling fans to protect against thermal overload and internal circuitry from damage due to
extreme heat. Please avoid covering any sides of the unit or placing objects or other audio devices too close to your mixer.
Prior to connecng and powering on the unit, make sure that the device matches the voltage and frequency of your
power supply. Power o the mixer when not in use.
Cables and Connecons
RCA
1/4'' TRS and Mono
XLR 3-Pin
RCA connector jacks have been most
commonly used in home audio systems
and conguraons for years. Also known
as RCA 'phono', 'plugs' or 'audio
connectors' , these jacks are always
unbalanced, and generally carry a line-
level signal at 10 dB, nominal signa–l
levels. The RCA connector jacks are most
likely used when connecng an audio
device like a media player or other home
audio type source to your mixer. These
connector jacks are also used when
connecng to the output of your devices.
1/4'' mono and stereo connector jacks are
labeled for use as unbalanced mono,
unbalanced stereo, balanced mono, or as
an insert patch point. A 1/4'' TRS (Tip,
Ring, Sleeve), 3-conductor connecon, or
'Stereo' cable allows a single connecon
signal to carry 2-channels of audio; also
can be used for mono balanced signals.
While, a 1/4'' TS (Tip, Sleeve), 2-conductor,
or 'Mono' cable are most popularly known
for their use in guitar or line-level
instrument connecon; they can also be
used for mono unbalanced signals.
XLR connector jacks, almost always carries
a balanced signal. Depending on your
device, these connector jacks may also be
capable of handling unbalanced signals.
Microphones generally have this type of
connector, as well as most other
professional audio equipment and devices.
Typical 3-Pin XLR sockets are xed with the
right-most pin being the 'ground', the le-
most pin being 'hot' and the boom pin
as the 'neutral'.
Technical Specicaons
Mono Inputs
Microphone Inputs (XENYX Mic Preamp)
XLR, electronically balanced, discrete input circuit
Mic E.I.N. (20Hz - 20kHz)
@ 0 Ohm Source Resistance
@50 Ohm Source Resistance
@150 Ohm Source Resistance
-134dB / 135.7dB A-Weighted
-131dB / 133.3dB A-Weighted
-129dB / 130.7dB A-Weighted
Frequency Response
<10Hz - 150kHz (-1dB)
<10Hz - 200kHz (-3dB)
Gain Range
+10dB to +60dB
Maximum Input Level
+12dB @ +10dB Gain
Impedance
Approximately 2.6k Ohm, Balanced
Signal- -Noise to
110dB / 112dB A-Weighted
Distoron (THD +N)
0.005% / 0.004%, A-Weighted
Line Input
1/4'' TRS Connectors, Electronically Balanced
Channel Equalizaon
(Frequency Hz)
Control Range High: @ 10k +/-15dB
Control Range Low: k +/-15dB @60
Master 5-Band Graphic EQ
Frequency: Hz (60, 250, 1K, 4K, 12K)
Control Ranges: +/-12dB
Specyfikacje produktu
| Marka: | Pyle |
| Kategoria: | Ręczny blender |
| Model: | PMX802M |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Pyle PMX802M, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ręczny blender Pyle
23 Września 2024
22 Września 2024
20 Września 2024
7 Września 2024
1 Września 2024
31 Sierpnia 2024
25 Sierpnia 2024
25 Sierpnia 2024
23 Sierpnia 2024
22 Sierpnia 2024
Instrukcje Ręczny blender
- Ręczny blender Muse
- Ręczny blender Exquisit
- Ręczny blender Krups
- Ręczny blender GE
- Ręczny blender KitchenAid
- Ręczny blender Mystery
- Ręczny blender Bosch
- Ręczny blender Braun
- Ręczny blender Studio
- Ręczny blender Home Electric
- Ręczny blender Klark Teknik
- Ręczny blender Oster
- Ręczny blender Swan
- Ręczny blender Concept
- Ręczny blender Taurus
Najnowsze instrukcje dla Ręczny blender
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025
16 Stycznia 2025