Instrukcja obsługi Roland C-280

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Roland C-280 (5 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 27 osób i została oceniona przez 4 użytkowników na średnio 4.5 gwiazdek

1

Classic OrganDate: Oct. 1. 1999

Model: C-280

MIDI IMPLEMENTATION

Version: 1.00

1.Receive data

■

Channel Voice Messages

●

Note o

Status2nd byte3rd byte

8nH kkH vvH

9nH kkH 00H

n = MIDI channel number: 0H-FH (ch.1-ch.16)

kk = note number: 00H-7FH (0-127)

vv = note o velocity: 00H-7FH (0-127)

●

Note on

Status2nd byte3rd byte

9nH kkH vvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

kk = note number: 00H-7FH (0-127)

vv = note on velocity: 01H-7FH (1-127)

*Note numbers outside the range of 18-113 are transposed to the nearest octave within

this range.

*Transpose function does not aect the recognized note numbers.

●

Control Change

*The value specied by a Control Change message will not be reset even by a Program

Change, etc.

❍

Data Entry (Controller number 6, 38)

Status2nd byte3rd byte

BnH 06HmmH

BnH 26HllH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm, ll = the value of the parameter specied by RPN

*Data entry messages are recognized only when received on the basic channel.

❍

Volume (Controller number 7)

Status2nd byte3rd byte

BnH 07HvvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Volume: 00H-7FH (0-127), Initial Value = 7FH (127)

❍

Expression (Controller number 11)

Status2nd byte3rd byte

BnH 0BHvvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Expression: 00H-7FH (0-127), Initial Value = 7FH (127)

❍

Hold 1 (Controller number 64)

Status2nd byte3rd byte

BnH 40HvvH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON

❍

RPN MSB/LSB (Controller number 100, 101)

Status2nd byte3rd byte

BnH 65HmmH

BnH 64HllH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

mm = upper byte of parameter number specied by RPN

ll = lower byte of parameter number specied by RPN

*The value specied by RPN will not be reset even by messages such as Program Change

or Reset All Controller.

*RPN messages are recognized only when received on the basic channel.

**RPN**

The RPN (Registered Parameter Number) messages are expanded control changes, and each

function of an RPN is described by the MIDI Standard.

To use these messages, you must rst use RPN MSB and RPN LSB messages to specify the

parameter to be controlled, and then use Data Entry messages to specify the value of the

specied parameter. Once an RPN parameter has been specied, all Data Entry messages

received on that channel will modify the value of that parameter. To prevent accidents, it is

recommended that you set RPN Null (RPN Number = 7FH/7FH) when you have nished

setting the value of the desired parameter.

On the C-280, RPN can be used to modify the following parameters.

RPNData entry

MSB LSBMSB LSBExplanation

00H 01HmmH llHMaster Fine Tuning

mm, ll: 00 00H - 40 00H - 7F 7FH (-100 - 0 - +99.99

cents), Initial Value = 40 00H (± 0 cent)

7FH 7FH--- ---RPN null

Set condition where RPN and NRPN are

unspecied. The data entry messages after set

RPN null will be ignored.

(No Data entry messages are required after RPN

null).

Settings already made will not change.

mm, ll: ignored

●

Program Change

Status2nd byte

CnH ppH

n = MIDI channel number: 0H-FH (ch.1-ch.16)

pp = Program number: 00H..37H (prog.1..prog.56)

Received program change message are assigned as follows.

prog. tone

1Organ Manual

2Ensemble Chime

3Ensemble Celesta

4Ensemble Choir

17Ensemble Chime + Organ Manual

33Ensemble Celesta + Organ Manual

49Ensemble Choir + Organ Manual

*“+” indicatesadualtone.'

*Program numbers not in the above table are ignored.

*The switch to the requested Ensemble Tone is made when the rst new Note On

message arrives after the Program Change has been received. Organ Tones are changed

immediately after reception of the Program Change.

*When the C-280 receives Program Change messages that include requests for Organ

Tones, the [Manual] button is selected.

*Organ Tones are set by mean of Program Changes, and System Exclusive messages that

indicate the status of Draw knobs.

For more information about the System Exclusive messages that indicate the status of

Draw knobs, refer to "3. Parameter Address Map."

Copyright © 2001 ROLAND CORPORATION

All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.

Specyfikacje produktu