Instrukcja obsługi Samsung AG070KSVGNH

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Samsung AG070KSVGNH (2 stron) w kategorii klimatyzacja. Ta instrukcja była pomocna dla 29 osób i została oceniona przez 3 użytkowników na średnio 4.9 gwiazdek

1 2 3 4

8765

3 Press K1 shortly to display the number for selected option.

4 Press K2 shortly to display the number for set value of the selected option.

5 Finish the option setting.

fPress K2 long to nish the setting with all option values determined and saved.

fPress K1 long to nish the setting with all option values cancelled and keep the values as before entering the setting.

• In option setting, press K4 long to initialize all option values.

No.Option itemOption

value

Factory

default OptionDenitionSetting unit

Module control

setting option

Note1)

1Operation On/Off input method0·1 00Module control/DMSMain unit of group

Note2)

1External contact

2Temperature setting input method0·100Module control/DMSMain unit of group

Note2)

1External contact

3Operation mode (Cool/Heat, normal/hot water) input method0·100Module control/DMSMain unit of group

Note2)

1External contact

4Demand control input method0·100Module control/DMSMain unit of group

Note2)

1External contact

53Demand level0 ~ 11

0Default (100 %)

Main unit of moduleO

195 %

290 %

385 %

480 %

575 %

670 %

765 %

860 %

955 %

1050 %

11Not applied (No limit)

60Quiet function input method0·10Module control/DMSMain unit of group

Note2)

1External contact

7Forced fan function input method0·100Module control/DMSMain unit of group

Note2)

1External contact

8Water law input method0·100Module control/DMSMain unit of group

Note2)

1External contact

90Pump operation when thermo off0·10Pump OFF when thermo OFF and operation

pattern is not standard controlMain unit of module

1Pump ON always when thermo OFF

10Remote error reset input0·100Disuse Main unit of module

1 Use

11

Setting unit address

• Module address must be set. (Refer to installation

manual of module controller.)

0 ~ 15(Not set)Setting unit addressEach unit

12Quiet function level0 ~ 31

0Default (100 %)

Main unit of moduleO

1 Level1

2 Level2

3 Level3

13Conrm delay for unsecured ow rate when operating10 ~

240 30 Delay for inspecting no input for pump

interlock and unsecured ow rate (by seconds)Main unit of module

14Using exterior water outlet temperature sensor0/100DisuseMain unit of group

Note2)

1 Use

15Water law control standard0/10

0Outdoor temperatureMain unit of group

Note2) O

1Room temperature (external room temperature

sensor installation necessary)

16AirCool1 (For water law)0 ~ 20Standard 1 outdoor temperature for cooling10

Main unit of group

Note2) O

17AirCool2 (For water law)30 ~ 40Standard 2 outdoor temperature for cooling35

18RoomCool1 (For water law)15 ~ 24Standard 1 room temperature for cooling20

19RoomCool2 (For water law)25 ~ 35Standard 2 room temperature for cooling30

20Tcool1 (For water law)-10 ~

25 15Standard 1 set temperature for cooling

21Tcool2 (For water law)-10 ~

25 7Standard 2 set temperature for cooling

22AirHeat1 (For water law)-20 ~ 5Standard 1 outdoor temperature for heating-10

23AirHeat2 (For water law)10 ~ 20Standard 2 outdoor temperature for heating15

24RoomHeat1 (For water law)15 ~ 24Standard 1 room temperature for heating20

25RoomHeat2 (For water law)25 ~ 35Standard 2 room temperature for heating30

26Theat1 (For water law)35 ~ 55Standard 1 set temperature for heating45

27Theat2 (For water law)35 ~ 55Standard 2 set temperature for heating35

28Operation ON/OFF by external contact0/100Recognize usual signalMain unit of group

Note2)

1Recognize instant signal

29 ~ 33Function expansion available

34Using low temperature function0/100 DisuseEach unit

1 Use

35 ~ 37Function expansion available

Note1) For options that can be selected by module control and main option, the option value selected for last time will be saved.

Note2) Main unit of module when group is not available

Setting hydro unit option and key function (Continued)

Function description

No. Description

1

Select operation On/Off input method of module/group

2

Select temperature setting input method of module/group

3

Select operation mode (Cool/Heat, Hot water/Cool storage) input method of

module/group

4

Select demand control input method of module/group

5

Select demand level

• Current will be limited below the set level when "Perform" command

is transmitted.

6

Select quiet function input method of module

7

Select forced fan function input method of module

• Forced fan: Removes accumulated snow by operating the fan of

stopped unit in low frequency

• Snow accumulation prevention, which operates occasionally when

outdoor temperature is below zero, is basic function.

8

Select water law input method of module/group

9

Select pump operation status when thermo OFF

10

Select to use error clear function by external contact

11

Setting CHILLER unit address: identical with channel address used by DMS

12

Select quiet function level

• Quiet function will start in set level when "Perform" command is

transmitted.

• Level comparison: Level3 > Level2 > Level1

13

Conrm delay for unsecured ow rate when operating: Delay for inspecting

no input for pump interlock and unsecured ow rate

• Compressor will not operate until water ow is detected.

14

Set when controlling water outlet temperature by installing extra water

temperature gauge on water pipe header or tank

• External water outlet temperature sensor should be installed on main

unit of group (or module when group is not available).

• Standard for water outlet temperature depends on external water

outlet temperature sensor except when operation pattern is standard

control.

15

Setting water law standard

• To set room temperature as stnadard, external room temperature

sensor should be installed.

• Room temperature sensor should be installed on main unit of group (or

module when group is not available).

16 ~ 27

Water law control constant: Refer to water law operation graph.

28

Recognition of external control operation ON/OFF

• 0 (recognizing usual signal): Constantly inspects ON/OFF status of

contact and set operation ON/OFF

• 1 (recognizing instant signal): Set operation ON/OFF when contact

ON/OFF signal is input (when external contact is consisted of button

click)

34

Select to use low temperature function

• The function will operate when set simultaneously with product

option of module control (Seg23 of installation option 02 = 'E')

• Low temperature function: Expands water outlet usage range in Cool/

Cool stoarge mode ( 5 ~ 25 °C  -10 ~ 25 °C)

• When using low temperature function, use brine and maintain the

concentration under freezing point.

MICOM version display

fPress and hold K3 and K5 for 3 seconds to enter the view mode.

fPress K3 to change view mode in order of the table.

fCancelling view mode display

-Press and hold K3 for 3 seconds.

SEG1 SEG2 SEG3 SEG4 SEG5 SEG6RemarksData

Source

Address

setting

mode

0 1 0 1 1 2Hydro

controller

Main

MICOM

version

Mn 1 5 1 1

ex) ver

151101 

1511

Inverter

controller

Hub MICOM

version H b 1 3 0 2

ex) ver

130228 

1302

Inverter

controller

Inverter 1

version I1 1 3 0 2

ex) ver

130228 

1302

Inverter

controller

Inverter 2

version I2 1 3 0 2

ex) ver

130228 

1302

Inverter

controller

Fan 1

version F 1 1 3 0 2

ex) ver

130228 

1302

Inverter

controller

Fan 2

version F 2 1 3 0 2

ex) ver

130228 

1302

Inverter

controller

EEP versionEP1511

ex) ver

151101 

1511

Inverter

controller

Hydro

version H d 1 5 1 1

ex) ver

151101 

1511

Hydro

controller

Setting inverter controller option

Basic segment display

StepDisplay contents

Display

SEG1SEG2 SEG3 SEG4

At initial power

supply

Checking segment

display 8 8 8 8

Setting

communication

(Addressing)

-A d 0 1

After communication

setting (usual

occasion)

Transmit/Reception

address

Hydro

controller:

A

Hydro

controller:

0

0 0

Installing and setting the option with tact

switch and functions

1 Press and hold K2 for 3 seconds. (Only available when the operation is

stopped)

fThe display will show the following.

fIf you have set the Emergency operation for compressor malfunction, 1

or 2 will be displayed on Seg 4.

-Seg 1 and Seg 2 will display the number for selected option.

-Seg 3 and Seg 4 will display the number for set value of the

selected option.

2 If you have entered option setting, you can shortly press the K1 switch

to change the value of the Seg 1 and Seg 2 to select desired option.

fRefer to the table for the Seg number of the function for each option.



3 If you have selected desired option, you can shortly press the K2 switch

to change the value of the Seg 3 and Seg 4 to change the functional

setting for the selected option.

fRefer to the table for the Seg number of the function for each option.



4 After selecting the function for options, press and hold the K2 switch

for 2 seconds. Entire 7-segment will blink to begin tracking mode and

value of the option will be be saved. If you do not end the setting mode

properly, option will not be saved.

Option itemInput

unit SEG1 SEG2 SEG3 SEG4Function of the

option Remarks

Emergency

operation for

compressor

malfunction

Individual 00

0 0Disabled E560 will occur

when all the

compressors

are set as

malfunction

state.

01 Set compressor 1 as

malfunction state

02 Set compressor 2 as

malfunction state

Oil collection

interval Main 04

00Factory default

01 Shorten the interval

by 1/2

Temperature

to trigger

defrost

operation

Main 05

00Factory default

0 1

Apply setting when

the product is being

installed in humid

area such as near

river or lake

Outdoor unit

fan speed

correction

Individual 06

00Factory default

01Increase fan speed

Increase the

outdoor unit

fan speed to

maximum value

Snow

accumulation

prevention

function Note1)

Main 14

00 Enabled (Factory

default)

During snow

accumulation,

the fan may spin

even when the

unit is not in

operation

0 1Disabled

Maximum

cooling

capacity

restriction

Note2)

Main 18

0 0Enabled

0 1Disabled

Note1)

Snow accumulation prevention function: Operates fan periodically to

prevent show compiling on the fan while the product is stopped

Note2)

Maximum cooling capacity restriction: Limits operation capacity of

compressor according to indoor load

Setting key operation and checking the view

mode with tact switch

K1 K2 K3 K4

K1

(Number

of press)

KEY operationDisplay on 7-Segment

1 timeRefrigerant charging in Heating mode

2 timesTrial operation in Heating mode

3 timesRefrigerant discharging in Heating mode

4 timesDisuse

5 timesDisuse

6 timesDisuse

7 timesVacuum

8 timesDisuse

9 timesDisuse

10 timesDisuse

11 timesDisuse

12 timesEnd KEY operation-

K2 (Number

of press)KEY operationDisplay on 7-Segment

1 timeRefrigerant charging

in Cooling mode

2 timesTrial operation in

Cooling mode

3 timesPump down all units

in Cooling mode

4 timesAuto trial operation

5 timesChecking the amount

of refrigerant

X X

(Display of last two digits may differ depending

on the progress)

6 timesDischarge mode of

DC link voltage

7 timesForced defrost

operation

8 timesForced oil collection

9 timesInverter compressor

1 check

10 timesInverter compressor

2 check

11 timesFan 1 check

12 timesFan 2 check

13 timesEnd KEY operation-

fTo use key operating function for service and maintenance when

installing module/group, set as main control or cancel in module/group.

fDuring Discharging mode, voltage of Inv1 and Inv2 will be displayed

alternately.

fEven when the power is off, it is dangerous when you come in contact

with inverter PCB, fan PCB since high pressure DC voltage is charged to

those parts.

fWhen replacing or repairing the PCB, cut-off the power and wait until

the DC voltage is discharged before replacing/repairing them.

-Wait for more than 15 minutes to allow those parts to be fully

discharged.

fWhen there is error, Discharge mode of DC link voltage may not have

been effective. Especially when E464 and E364 error is displayed,

power element might be damaged so do not use the Discharge mode of

DC link voltage.

K3 (Number

of press)KEY operationDisplay on 7-Segment

1 timeIntialize (Reset) operationSame as initial state

K4 (Number

of press)Display contents

Display

SEG1SEG2, 3, 4

1 timeCapacity depending on

horsepower 1

AG042KTTT0, 1, 5

AG056KTTT0, 2, 0

AG070KTTT0, 2, 5

2 timesOrder frequency (Compressor 1)120 Hz 1, 2, 02

3 timesOrder frequency (Compressor 2)120 Hz 1, 2, 03

4 timesHigh pressure (MPa)1.52 MPa 1, 5, 24

5 timesLow pressure (MPa)0.43 MPa 0, 4, 35

6 timesDischarge temperature

(Compressor 1)6 87°C 0, 8, 7

7 timesDischarge temperature

(Compressor 2)787°C  0, 8, 7

8 timesIPM temperature (Compressor 1)887°C  0, 8, 7

9 timesIPM temperature (Compressor 2)987°C  0, 8, 7

10 timesCT sensor value (Compressor 1)2 A 0, 2, 0A

K4 (Number

of press)Display contents

Display

SEG1SEG2, 3, 4

11 timesCT sensor value (Compressor 2)2 A 0, 2, 0B

12 timesSuction 1 temperatureC-42°C  0, 4, 2

13 timesCOND Out temperature -, 4, 2D-42°C 

14 timesTemperature of liquid pipeE-42°C  -, 4, 2

15 timesTOP temperature (Compressor 1)F-42°C  -, 4, 2

16 timesTOP temperature (Compressor 2)G-42°C  -, 4, 2

17 timesOutdoor temperatureH-42°C  -, 4, 2

18 timesEVI inlet temperatureI-42°C  -, 4, 2

19 timesEVI outlet temperatureJ-42°C  -, 4, 2

20 timesMain EEV 1 step2000 steps K 2, 0, 0

21 timesMain EEV 2 step2000 steps L 2, 0, 0

22 timesEVI EEV step300 steps 3, 0, 0M

23 timesH/R EEV step300 steps 3, 0, 0N

24 timesFan step (SSR or BLDC)13 steps 0, 1, 30

25 timesCurrent frequency

(Compressor 1)P120 Hz 1, 2, 0

26 timesCurrent frequency

(Compressor 2)Q120 Hz 1, 2, 0

27 timesSuction 2 temperatureR-42°C  -, 4, 2

28 timesMain Hydro controller addressS

Main Hydro controller not

selected  BLANK, N, D

If Hydro controller No.1 is

selected as the main unit 

0, 0, 1

29 timesSnow accumulation sensor

voltage T1.80 V 1, 8, 0

30 timesTotal suction temperatureU-42°C  -, 4, 2

K4 (Number

of press)

(Press and

hold the

K4 for 3

seconds to

enter the

setting)

Display contents

Display

Page1 Page2

1 timeMain versionVersion (ex.: 1412)MAIN

2 timesHub versionVersion (ex.: 1412)HUB

3 timesInverter compressor 1 checkVersion (ex.: 1412)INV1

4 timesInverter compressor 2 checkVersion (ex.: 1412) INV2

5 timesFan 1 checkVersion (ex.: 1412)FAN1

6 timesFan 2 checkVersion (ex.: 1412)FAN2

7 timesEEP versionVersion (ex.: 1412)EEP

8 timesAutomatically assigned

address of the unitsAUTO

Seg1Seg2Seg3, 4

Hydro

controller:

A

Hydro

controller:

0

Address

(ex.: 07)

9 timesManually assigned address

of the unitsMANU

Seg1Seg2Seg3, 4

Hydro

controller:

A

Hydro

controller:

0

Address

(ex.: 15)

A-T/B B-T/B

C-T/B

1 3 57911131517192 4 68101214161820

1 3 57911131517192 4 68101214161820

1 3 57911131517192 4 68101214161820

A-T/B

B-T/B

C-T/B

External contact wiring work

Installation date

YY / MM / DD

Trial operation date (YY) (MM) (DD)

Installation company

Name

Installer

Name

Contact Contact

Installer CODE

Quality guidanceName Quality instructorName

Contact Contact

ModelPurpose □Room temp.

□Low temp.

□How water

□Others

Serial number

Cooling

Rated capacity kW

Remarks Chiller water

condition

Outlet: °C Inlet: °C

Chilled water storage: l/min Pump pressure: kPa

Outdoor temp.

condition °CDB °CWB

Water pipe equipment installation

Heating

Rated capacity kW

Installation date

YY / MM / DD

Heating water

condition

Outlet: °C Inlet: °C

Trial operation date

YY / MM / DDChilled water storage: l/min Pump pressure: kPa

Water pipe installation

company

Name

Outdoor temp.

condition °CDB °CWB

Contact

Contact

Pump included/excluded□excluded □included

Brine spec.

Type

Pump typePrimary (Cooler) □Fixed □Inverter

Secondary (Load) □Fixed □Inverter

Concentration

f

Samsung's product is irrelevant to any installation or performance problem of the water pipes and boiler.

f

This installation specications of the Samsung products will be managed as a reference for follow-up management.

Installation manager self-maintenance list

Preparation

Parts DescriptionStandard

Results

Cabinet panel

board Is power withdrawn by auxiliary circuit breaker?Must use auxiliary circuit breaker

Power Is outdoor cable conncected in order of RST power?Visual check

Is power cable fastened with rated torque value by solderless ring terminal?Ring terminal and tighteing torque (by visual check)

CommunicationIs module control connected to F3/F4 of hydro PBA?

Cooler

Is service area around the product appropriate?Check standard in installation manual

Is installation location Check standard in installation manual

Are supporting base and vibration-isolation pad applied properly according to installation manual?Visual check

Are drain valves installed?Visual check

Is option switch setting for each type of heat source water appropriate? (heat source water / brine)Visual check

Water supply

system

Is there no leakage on water pipe?Visual check

Are temperautre gauges and pressure gauges installed on water pipe inlet/outlet?Visual check (4)

Air valves and exible joints installed on water pipe inlet/outlet?Visual check (4)

Check cleaning of foreign materials inside the water supply system and welding slugsCheck if ushing is done/Water quality check

Is strainer cleaned on water pipe inlet?Cleaning

Are air vent valves and drain valves installed for drainage?Visual check

Is there countermeasure for balancing supplying ow rate?

Visual check for reverse return pipe or rated ow rate valve components

Is expansion tank installed?Visual check

Is water supplied according to standard of supply water quality?Check water quality

Trial operationCooler

Is temperature of inlet/outlet appropriate?Check temperature gauge (according to installation manual)( )°C

Is ow rate within the range of max./min. supplying ow rate?Check standard in installation manual( ) LPM

Is pressure difference between inlet/outlet on water pipe pressure sensor?Check standard in installation manual( ) kPa

DVM CHILLER condition check card

Installation check card

Installation date (YY) (MM) (DD)

Outdoor unit model

Outdoor unit serial number

Outdoor unit circuit breaker

Circuit breaker capacity [A]

Power cable [mm2]

Remarks

Trial operation date (YY) (MM) (DD)

Installer

Name

Contact

Installer CODE

Installation

company

Name

Contact

Quality

instructor

Name

Contact

Product

outline

Name

Site

Route

Period

Spec.

Purpose □

General □Yearly □

Process □

Others

A

Cooling

Rated capacity kW

Chilled water

condition

Outlet: °C Inlet: °C

Chilled water storage: l/min

Pump pressure: kPa

Outdoor

temperature

condition

°CDB °CWB

Heating

Rated capacity kW

Heating water

condition

Outlet: °C Inlet: °C

Chilled water storage: l/min

Pump pressure: kPa

Outdoor

temperature

condition

°CDB °CWB

B

Power

□

50Hz □

60Hz

□

3 Phase 200V □

Others (Phase V)

Pump type□

Individual (included/excluded) □

Assembled

Special condition□

Public building □

Chloride corrosion

□

Sea water □Brine □

Split division

Electrical parts list

□

Max. capacity limit

□

Pump capacity ( kW)

□

Assembling active lter(5kVA)

□

Power cable kit

□Fin protection

□Others( )

Piping type□

1 pump (Pump on heat source: Fixed. Variable.)

□

2 pump (Pump on heat source: Fixed. Variable)

Number of control unit□

Classifying maker (module control)

□

Classifying electrical parts maker ( )

Error display

fSegment will display error code (4 digit).

HYDRO-UNIT_MODULE_CHILLE

K1K2 K3 K4K5 K6

88-SEG DISPLAY

Display Description

101

Communication error between hydro controller and inverter controller (If

not received for 3 minutes from outdoor unit)

108

Error due to repeated setting address

109

Communication error of hydro controller address not complete

122

Error on hydro Evap in Sensor (Open/Short)

123

Error on hydro Evap out Sensor (Open/Short)

128

Error on hydro Evap in Sensor (Detached)

129

Error on hydro Evap out sensor (Detached)

144

Error on hydro pipe temperature 2 sensor

145

Error on hydro EVA OUT 2 sensor

151

Hydro EEV open error (2nd detection)

152

Error due to closed EEV of hydro (2nd detection)

153

Error on hydro oating switch (2nd detection)

162

Inverter controller EEPROM error

163

Hydro controller EEPROM option setting error

198

Error due to disconnected thermal fuse (Temperature of terminal block

increases.)

201

Communication error between hydro controller and outdoor unit

202

Communication error between hydro controller and inverter controller

(When there is no response from indoor units after tracking is completed)

203

Communication error of Main and sub MICOM of inverter controller

205

Communication error of inverter controller main PBA - sub PBA (Sub PBA

communication all not received)

206

Communication error of inverter controller main PBA - sub PBA (Sub PBA

communication partially not received)

Specication of PBA display for actual communication error

C001: Hub PCB communication error

C002: Fan PCB communication error

C003: INV1 communication error

C004: INV2 communication error

221

Error on outdoor temperature sensor (Short or Open)

231

Error on COND outlet sensor (Short or Open)

241

COND outlet sensor is detached

251

Error on discharge temperature of COMP1 (Short or Open)

257

Error on discharge temperature of COMP2 (Short or Open)

262

Discharge temperature sensor of COMP1 is detached

263

Discharge temperature sensor of COMP2 is detached

266

Top1 temperature sensor is detached

267

Top2 temperature sensor is detached

269

Suction temperature sensor is detached

270

Suction 2 temperature sensor is detached

276

Error on Top 1 temperature sensor (Short or Open)

277

Error on Top 2 temperature sensor (Short or Open)

291

Error on high pressure sensor (Short or Open)

296

Error on low pressure sensor (Short or Open)

308

Error on Suction sensor (Short or Open)

311

Error on double layer pipe sensor (Short or Open)

321

EVI inlet temperature

322

EVI outlet temperature

323

Error on Suction 2 sensor (Short or Open)

326

Error on Total suction sensor (Short or Open)

346

Operation failure of Fan2

347

Unconnected error of Fan2

348

Lock error on Fan2

353

Overheated motor of Fan2

355

Error due to overheated IPM of Fan2

361

INV2 Comp starting error

364

INV2 DC Peak error

365

INV2 Comp Vlimit error

366

INV2 DC-Link voltage under/over error

Display Description

367

INV2 Comp Rotation error

368

Error due to full current of INV2

369

INV2 DC Link sensor error

371

INV2 DataFlash error

374

INV2 IPM Heat Sink error

378

Error due to overcurrent of Fan2

383

Error due to special overcurrent of Fan2

385

INV2 input current error

386

Error due to over voltage/low voltage of Fan2

387

Hall IC error of Fan2

389

Outdoor fan2 overload stop

391

Fan2 Date Flash error

393

Fan2 DC output sensor error

396

Fan2 DC Link voltage sensor error

399

Heat sink temperature sensor error of Fan2

400

INV2 IPM OverHeat error

407

COMP down due to high pressure

410

COMP down due to low pressure

416

COMP down due to discharge temperature

425

Phase reversal or phase failure

428

COMP down due to compressor not controlled

438

EVI EEV open error

439

Error due to refrigerant leakage (Examine when system off)

440

Restriction of heating operation by outdoor temperature

441

Restriction of cooling operation by outdoor temperature

442

Restriction of heating charging operation by outdoor temperature

443

Operation prohibited due to low pressure

445

Error due to self-diagnosis of CCH

446

Operation failure of Fan1

447

Unconnected error of Fan1

448

Lock error on Fan1

452

Instant blackout error

453

Overheated motor of Fan1

455

Error due to overheated IPM of Fan1

461

INV1 Comp starting error

462

Compressor stop due to full current control or error due to low current

on CT2

464

INV1 DC Peak error

465

INV1 Comp Vlimit error

466

INV1 DC-Link voltage under/over error

467

INV1 Comp Rotation error

468

Error due to full current of INV1

469

INV1 DC Link sensor error

471

INV1 Date Flash error

474

INV1 IPM Heat Sink error

478

Error due to overcurrent of Fan1

483

Error due to special overcurrent of Fan1

485

INV1 input current error

486

Error due to over voltage/low voltage of Fan1

487

Hall IC error of Fan1

489

Outdoor fan1 overload stop

491

Fan1 DataFlash error

493

Fan1 DC output sensor error

496

Fan1 DC Link voltage sensor error

499

Heat sink temperature sensor error of Fan1

500

INV1 IPM OverHeat error

560

Switch option setting error

901

Hydro inlet temperature sensor (Tw1) Short/Open

902

Hydro outlet temperature sensor (Tw2) Short/Open

907

Frozen damage error

908

Error when freeze prevention Comp Off occurs 4times

909

Error when freeze prevention Comp Off occurs 3times

910

Error on hydro outlet temperature (Tw2) sensor (Detached)

911

Flow switch option error

913

Flow switch error (E911) occurs 6 times

918

Error on pump magnetic switch malfunction

971

External sensor (WaterOut Setting Device/ WaterLaw Room Temp sensor)

is open/Short

972

Water inlet side pressure sensor is open/short

973

Water outlet side pressure sensor is open/short

974

External WaterOut sensor is open/short

Error CodeSetting hydro unit option and key function

Setting hydro unit option and key function

View mode display

fPress and hold K3 and K4 for 3 seconds to enter the view mode.

fPress K3 to change view mode in order of the table.

fPress K4 to change view mode in reverse order of the table.

fCancelling view mode display

-Press and hold K3 for 3 seconds.

K1 K2 K3 K4 K5 K6

88-SEG DISPLAY

TACT S/W

DIP S/W

Number of pressKEY operationSEG1SEG2SEG3SEG4SEG5SEG6Remarks

1 timeWater Inex) -5°C01-050

2 timesWater Outex) -11°C02-110

3 timesOutdoor temperatureex) -11.2°C03-112

4 timesHigh pressureex) 29.3 kgf/cm042932G

5 timesLow pressureex) 7.5 kgf/cm050752G

6 timesComp 1 current frequencyex) 110Hz06110

7 timesComp 2 current frequencyex) 113Hz07113

8 timesDischarge 1 temperatureex) 101.8°C 08101 101 (Drop)

9 timesDischarge 2 temperatureex) 101.8°C 09101 101 (Drop)

10 timesTop 1 temperatureex) 101.8°C 10101 101 (Drop)

11 timesTop 2 temperatureex) 101.8°C 11101 101 (Drop)

12 timesTotal suction temperatureex) -11.2°C12-112

13 timesSuction 1 temperatureex) -11.2°C13-112

14 timesSuction 2 temperatureex) -11.2°C14-112

15 timesCOND Out temperatureex) -11.2°C15-112

16 timesLiquid Temperatureex) 35°C16350

17 timesEVA In 1 temperatureex) 35°C17350

18 timesEVA Out 1 temperatureex) 50°C18500

19 timesEVA In 2 temperatureex) 35°C19350

20 timesEVA Out 2 temperatureex) 50°C20350

21 timesEVI In temperatureex) 35°C21350

22 timesEVI Out temperatureex) 35°C22350

23 timesIPM 1 temperatureex) 80°C23800

24 timesIPM 2 temperatureex) 80°C24800

25 timesCT 1ex) 11A25110

26 timesCT 2ex) 11A26110

27 timesOperation modeS:Thermal/Cool storage / C:Cooling, H:Heating27Blank/SC/H

28 timesSet temperatureex) -5°C28-050

29 timesPump output290n/FBlank/FOn/Off

30 timesFan Stepex) 24step 30024

31 timesHydro EEV 1ex) 1007step 31100 100 (Drop "/10")

32 timesHydro EEV 2ex) 1007step 32100 100 (Drop "/10")

33 timesMain EEV 1ex) 1007step 33100 100 (Drop "/10")

34 timesMain EEV 2ex) 1007step 34100 100 (Drop "/10")

35 timesEVI EEVex) 473step 35473

36 timesPHE inlet pressureex) 1.2 kgf/cm360122G

37 timesPHE outlet pressureex) 0.4 kgf/cm370042G

38 timesCapacity (Cooling)ex) 70 kW38070

39 times(Exterior) Room temperatureex) 25.5°C39255

40 times(Exterior) Water outlet temperatureex) -11°C40-110

41 timesPressure difference calibrationex) -0.2 kg/cm41-0022

How to set hydro controller option

Option No.Option value

SEG1 SEG2 SEG3 SEG4 SEG5 SEG6

Operation On/Off input method

01- - -0

Temperature setting input method

02- - -0

1 Turn on the product.

2 Press and hold the K2 to enter the option setting.

fIn option setting, other key input (forced fan, temperature setting, etc.) is not received.

DB68-05937A-01

No.NameSignalFunctionContact ShortContact OpenSignal

recognition Setting unit

A-T/B

1-2 Cooling/Heating display

Zero

voltage

contact

Display when operates in heating modeHeatCool--

3-4 Operation displayDisplay when operatesOperateStop--

5-6 Warning displayDisplay when error occursError occurredNo error--

7-8 Defrost operation displayDisplay when defrostingDeforst ONDefrost OFF--

9-10 Pump operation displayDisplay when pump operatesPump ONPump OFF--

11-12 Comp operation displayDisplay when compressoroperatesCompressor ONCompressor OFF--

13-14 Pump operationSignal of pump operationPump signal ONPump signal OFF--

15-16 Freeze protection displayDisplay when freeze protection operatesPump ON for freeze

protection Others --

17-18 Disuse ----

19-20 Disuse ----

B-T/B

1-2 Disuse ------

3-4 Disuse ------

5-6 Disuse ------

7-8 Pump interlock

Zero

voltage

contact

Signal about pump operation

• Pump interlock error (E918) occurs if ON is not input when operating pumpPump ONPump OFFUsual inputEach unit

9-10

Operation ON/OFFControlling operation ON/OFFUsual/instant

input Main unit of group

11-12

13-14 Operation modeSelecting cool/heat modeUsual inputMain unit of groupHeatCool

15-16 Hot water (Coolstorage)

mode

Entering hot water (cool storage) mode by external control

• Cool + ON: Cool storage

• Heat + ON: Hot water

Coolstorage/Hot

water Cool/HeatUsual inputMain unit of group

17-18 Hot water (Coolstorage)

control standard

Control depending on set temperature when ON

Control depending on external hot water (cool storage) thermostat when OFF

Control by set

temperature

Control by

thermostat Usual inputMain unit of group

19-20 Hot water (Coolstorage)

thermostat signal

When thermostat is set as standard for hot water (cool storage) mode

• Thermo ON when ON (Not over range of water outlet temperature)

• Thermo OFF when OFF

Thermo ONThermo OFFUsual inputMain unit of group

C-T/B

1-2 Quiet function

Zero

voltage

contact

Operate quiet function in level set by main option or module controlQuiet functionUsual inputMain unit of group-

3-4 Demand functionOperate demand function (current limet control) in level set by main opetion or module

control Demand functionUsual inputMain unit of group-

5-6 Forced fan functionOperate forced fan functionForced fan functionUsual inputMain unit of group-

7-8 Unusual condition resetReset on error occurred status

• Operates only when remote error reset input function is set to useReset errorInstant input-Main unit of

module

9-10 Disuse-----No use (N/A)

11-12 Water law

Zero

voltage

contact

Operate water lawWater law controlWater outlet set

temperature controlUsual inputMain unit of group

13-14 Disuse-----No use (N/A)

15-16 Disuse-----No use (N/A)

17-18 Set temperature/room

temperature sensor

Analog

current

Recognize water outlet set temperature by external input (4~20mA)

Recognize value of room temperature sensor (4 ~ 20 mA) when standard for water law

is room temperautre

--Current inputMain unit of group

19-20 External water outlet

temperature

Analog

current Recognize external water outlet temperature by external temperature sensor (4 ~ 20 mA)Current inputMain unit of group--