Instrukcja obsługi Schneider CCTFR6100Z3

Schneider termostat CCTFR6100Z3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Schneider CCTFR6100Z3 (6 stron) w kategorii termostat. Ta instrukcja była pomocna dla 24 osób i została oceniona przez 12.5 użytkowników na średnio 4.9 gwiazdek

Pobierz PDF

Strona 1/6

CCTFR6100Z3

en cs dabg en Wiser Radiator Thermostat

About this product

The Wiser radiator thermostat (hereinafter referred to

as ) uses integrated temperature sensors thermostat

to control the ow of water through a radiator, thereby

regulating the temperature in a room. The target

temperature and switching times are set in the Wiser

App.

! Package contents

A Radiator Thermostat

B O-ring (pre-installed)

C Chrome ring nut

D Danfoss RAVL

E Danfoss RA

F Danfoss RAV

G M30 x 1.5 valve adapter

H M4 hex nut

I M4 x 11.5 mm screw

J AA battery (pair)

K Installation guide

“ Removing the old radiator thermostat

Open the valve of the radiator thermostat to ‘max’

to facilitate removal. Unscrew ring nut and remove

thermostat.

Note: For other manufacturers please follow their

guidelines on how to remove the old radiator

thermostats.

§ Inserting the batteries

• When inserting batteries, observe the correct

polarity.

• Do not use rechargeable batteries.

A QR Code label

TIP: The QR code is used for secured Zigbee

commissioning which is an option in some Zigbee 3.0

systems. We strongly recommend not to remove this

label in case future commissioning is required.

HJ K

$ Install the adapter and thermostat

NOTICE

RISK OF DAMAGE TO EQUIPMENT

• Make sure that the O-ring is seated rmly on the

thread.

• Tighten the ring nut ensuring that the assembly is

not overtightened.

Failure to follow these instructions can result in

equipment damage.

Follow the installation steps for the type of adapter

you have.

A M30 x 1.5mm adapter

(1) Place the M30 adapter on the valve.

(1) Loosely screw the ring nut onto the valve

adapter.

(2) Screw on the thermostat and tighten.

B Danfoss RAVL to M30 adapter

(1) Place the Danfoss RAVL on the valve.

(3) Place the M30 adapter on the Danfoss RAVL.

(4) Loosely screw the ring nut onto the valve

adapter.

(5) Screw on the thermostat and tighten.

C Danfoss RA to M30 adapter

(1) Place the Danfoss RA on the valve.

(2) Assemble M4 hex nut and M4 x 11.5 screw to

tighten the Danfoss RA adapter onto the valve.

(3) Place the M30 adapter on the Danfoss RA.

(4) Loosely screw the ring nut onto the valve

adapter.

(5) Screw on the thermostat and tighten.

D Danfoss RAV to M30 adapter

(1) Break spindle adapter from the side of Danfoss

RAV.

(2) Place spindle adapter on the top of the valve

spindle and push fully on.

(3) Place the Danfoss RAV on the valve.

(4) Assemble M4 hex nut and M4 x 11.5 screw to

tighten the Danfoss RA onto the valve.

(5) Place the M30 adapter on the Danfoss RAV.

(6) Loosely screw the ring nut onto the valve

adapter.

(7) Screw on the thermostat and tighten.

NOTE: To align the LEDs in the desired position:

slightly loosen the ring nut, turn the thermostat to the

desired position and tighten the ring nut again.

% Read full device guide online

Scan the QR code and choose your language

for complete information about the device, including

operation, conguration and using the product with a

Wiser system.

Technical data

Power supply: 2x 1.5 V IEC LR6 (AA) alkaline

batteries

Without power supply: Connection data retained

Temperature setting range: 5 °C to 30 °C

Temperature resolution: 0.5 °C

Control accuracy: < 0.8 °C at 4 °C/h

Surface temperature at place

of installation:

max. 93 °C

Water temperature: max. 110 °C,

max. continuous 73 °C

Ambient operating

temperature:

0 °C to 45 °C

Storage temperature: -20 °C to 65 °C

Transportation temperature: -20 °C to 65 °C

Operating frequency: 2.4GHz

Max. radio frequency power

transmitted:

max. 20mW (13dBm)

Degree of contamination: 2

Radio range: 30 m free eld

Energy class: IV - 2%

Software class: A

Protection rating IP 30

Dimensions (HxØ): 93 x 51mm

Communication protocol: Zigbee 3.0 certied

Trademarks

• Wiser™ is a trademark and the property of

Schneider Electric SE, its subsidiaries and a󰀩liated

companies.

• Zigbee®

is a registered trademark of the

Connectivity Standard Alliance.

Other brands and registered trademarks are properties

of their relevant owners.

EU Declaration of Conformity

Hereby, Schneider Electric Industries, declares

that this product is in compliance with the essential

requirements and other relevant provisions of RADIO

EQUIPMENT DIRECTIVE 2014/53/EU. Declaration of

conformity can be downloaded on: se.com/docs.

Schneider Electric Industries SAS

If you have technical questions, please contact the

Customer Care Centre in your country.

se.com/contact

„ §

6 7

06490332001 Iss B

Specyfikacje produktu

Marka:	Schneider
Kategoria:	termostat
Model:	CCTFR6100Z3
Kolor produktu:	Biały
Wysokość produktu:	93 mm
Szerokość opakowania:	123 mm
Wysokość opakowania:	62 mm
Głębokość opakowania:	95 mm
Waga wraz z opakowaniem:	245 g
Stopień ochrony IP:	IP30