Instrukcja obsługi Sharper Image 20-Setting Beard and Stubble Trimmer
Sharper Image
Niesklasyfikowane
20-Setting Beard and Stubble Trimmer
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sharper Image 20-Setting Beard and Stubble Trimmer (5 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 22 osób i została oceniona przez 11.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/5
- 1 -
Item No. 205954
20-SETTING BEARD AND STUBBLE TRIMMER
User Guide
Thank you for purchasing the Sharper Image 20-Setting Beard and Stubble Trimmer. Please
read this User’s Guide carefully and keep it for future reference.
TO CHARGE/ RECHARGE
Fully charge Trimmer before using for the first
time or after non-use for a long period of time.
Charging, recharging or using the Trimmer in
temperatures than below 4°C (40° F) or higher
35°C (95° F) adversely affects lifespan of the
battery.
• If the Trimmer is subjected to a major change
in temperature, pressure or humidity, let the
trimmer acclimatize for 30 minutes before
using.
• Continuously recharging Trimmer will reduce
lifespan of battery.
1. Be certain Trimmer is OFF (Fig.1).
2. Connect appliance plug directly into the
Trimmer (Fig.2) and plug adapter into any
220-240 V AC outlet. Note: Use only the
included adapter plug provided.
3. The charging light on the adapter lights up
RED to indicate the Trimmer is charging. After
fully charging, the charging light will remain
lit. It will take approximately 10 hours to fully
charge the Trimmer for a cordless trimming
time of up to 45 minutes.
4. Disconnect the cord and unplug from
electrical outlet.
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
safety precautions should always be followed,
including the following. Read all instructions
before using this appliance.
To reduce the risk of electric shock:
1. Keep away from water.
2. Do not reach for a plugged in Trimmer that
has fallen into water. Unplug immediately.
3. The Trimmer is for dry use only. Do not use
while bathing or in a shower.
4. Do not place or store Trimmer where it can
fall or be pulled into a tub or sink.
5. Always unplug this Trimmer from the
electrical outlet immediately after (re)
charging.
6. Unplug and remove power supply cord from
Trimmer before cleaning.
FEATURES
1. Trimming Comb
2. Cutting Unit
3. Precision zoom
look adjustment
ring
4. ON/OFF switch
5. Socket for
appliance plug
6. Blade oil
7. Adapter
8. Cleaning brush
- 1 -
OPTIMIZE THE WORKING LIFE OF THE
BATTERY
• After the Trimmer has been charged for
the first time, do not recharge the Trimmer
between trimming sessions. Continue using it
until the battery is completely empty.
• Do not charge for more than 24 hours.
• Do not keep cord permanently plugged in.
• Discharge / run down the battery completely
twice a year by letting the motor run until it
stops.
• If the Trimmer hasn’t been used for a long
period of time, it must be recharged for a full
10 hours.
- 2 -
CORDLESS TRIMMING
1. Unplug Trimmer from outlet and remove
cord.
2. Slide ON/OFF switch ON to begin trimming.
3. When finished, turn Trimmer OFF.
TRIMMING
• Use this Trimmer for its intended household
use as described in this manual.
• Always comb the beard and/or moustache
with a fine comb before you start trimming.
• If you are trimming for the first time, be
careful. Do not move the Trimmer too fast.
Make smooth and gentle movements.
TRIMMING WITH YOUR BEARD
Trimming Comb (Note: Beard Trimming Comb
must be on Trimmer to use the Zoom Lock.)
1. Turn the Zoom Lock to the desired
trimming length setting (See table). The
setting is indicated in the center of the
adjustment ring (Fig. 3). If you are trimming
for the first time, start by using the comb
at the maximum trimming length setting
(#10) to prevent accidentally trimming
hairs too short. As you become familiar with
the settings, adjust Zoom Lock to desired
trimming length. Zoom Lock will “click” into
position at each setting.
2. Switch the Trimmer ON.
3. To trim in the most effective way, move
the Trimmer against the direction of hair
growth. Make sure the surface of the comb
always stays in contact with the skin
(Fig. 4).
4. If cut hairs have accumulated in the comb
turn Trimmer off, remove the comb and
shake the hair out of comb (Fig. 5). The
selected trimming length setting will not
change when you do this.
Trimming without the Beard Trimming comb
1. Be certain the Trimmer is in the OFF
position.
Setting Hair length after trimming
- 0.5 mm
1 1 mm
- 1.5 mm
2 2 mm
- 2.5 mm
3 3 mm
- 3.5 mm
4 4 mm
- 4.5 mm
5 5 mm
- 5.5 mm
6 6 mm
- 6.5 mm
7 7 mm
- 7.5 mm
8 8 mm
- 8.5 mm
9 9 mm
- 9.5 mm
10 10 mm
Trimming for ‘Stubble’ Look
5. Be certain Beard Trimmer Comb is on
Trimmer and use setting 1 (3/64in/1mm) to
result in a ‘stubble’ look (Fig. 6).
Trimming without the Beard Trimming comb
Remove comb if you are:
• Defining hair lines
• Trimming nape of neck
• Removing single, unwanted hairs
2. Remove the Beard Trimming Comb by pulling
it off the Trimmer (fig.7)
3. Switch the Trimmer ON.
4. Make well-controlled movements. Touch the
hair/skin lightly with the Trimmer (fig.8).
Specyfikacje produktu
| Marka: | Sharper Image |
| Kategoria: | Niesklasyfikowane |
| Model: | 20-Setting Beard and Stubble Trimmer |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Sharper Image 20-Setting Beard and Stubble Trimmer, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Sharper Image
19 Grudnia 2024
Sharper Image Surround Sound Shower System (Set of 2) Instrukcja
19 Grudnia 2024
19 Grudnia 2024
19 Grudnia 2024
Sharper Image 20-Setting Beard and Stubble Trimmer Instrukcja
19 Grudnia 2024
19 Grudnia 2024
Sharper Image Digital Temperature Display Fry Pan Instrukcja
19 Grudnia 2024
18 Grudnia 2024
Instrukcje Niesklasyfikowane
- Yaesu
- Akasa
- DAS Audio
- Markbass
- TOGU
- D-Link
- Rosco
- Aicon
- Old Blood Noise
- Milan
- Narva
- Trident
- Ninebot
- Hoshizaki
- Legamaster
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025