Instrukcja obsługi SIIG CE-H23C11-S1
SIIG
przedłużacz AV
CE-H23C11-S1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SIIG CE-H23C11-S1 (2 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 21 osób i została oceniona przez 11 użytkowników na średnio 4.6 gwiazdek
Strona 1/2
Important Instructions
• Suggest using IGMP Gigabit switches
• Do not mix up transmitter and receiver
before installation
• Channel of each transmitter(TX) must be
unique, otherwise, the system could break
down (including transmitter, receiver, IGMP
switch etc.)
Product Features
1. Resolution supported up to 1080p @60Hz
2. Transmission distance up to 120 meters (CAT6)
3. Support IR pass back function to control the
source device from RX location
4. Oers scalable TX/RX matrix conguration,
allows up to 256 total units, limited to 100
transmitters, additional transmitter units (part#
CE-H23B11) and receiver units (part# CE-
H23C11) sold separately
5. Supports computer control software to select
and switch between source devices
.
Package Contents
1. Transmitter unit
2. Receiver unit
3. User Guide
4. IR blaster extension cable
5. IR receiver extension cable
6. DC5V/2A power adapter (x2)
7. Remote control
8. 3 pin phoenix connector (x2)
9. Wall-mount kit (x2)
10. Screws (x8)
Layout
• Transmitter unit
OUTPUT GND RX TX
RS-232
1. IR window: remote control channel
2. Power indicator
3. TX ID: Indicator of the current TX’s number
4. Reset button
5. DC 5V/2A power jack
6. Data transmission indicator
7. RJ45 output
8. Connection indicator
9. IR blaster extension cable interface
10. HDMI local signal output
11. HDMI signal input
12. RS-232 connector
• Receiver unit
GND RX TX
RS-232
1. RX ID: Mark receiver unit as a number,
Indicator of the current RX’s number
2. IR window: remote control channel
3. Power indicator
4. TX connected: Indicator the input channel
as a number, and when the cahannel of
receiver as same as the channel of trans
mitter, transmission connected
5. Reset button
6. DC 5V/2A power jack
7. Data transmission indicator
8. RJ45 input
9. Connection indicator
10. IR receiver extension cable interface
11. HDMI signal output
12. RS-232 connector
Application
• Point to point
R
J
-
4
5
O
U
T
O
U
T
P
U
T
R
S
-
2
3
2
G
N
D
R
X
T
X
R
J
4
5
I
N
R
S
-
2
3
2
G
N
D
R
X
T
X
• Matrix conguration
Note: Dedicated LANs with IGMP Gigabit Ethernet switches are
recommended for reliable performance. Installing on mixed LANs
may adversly eect performance is not supported.
RS232 bi-direction function
• Baud rate
Different encoding mechanism can not mix-
connected, the baud rate of RS232 serial of these
transmitter unit and receiver unit, support 2400,
4800, 9600, 19200, 28800, 38400, 57600, and
115200
If the RS232 serial does not work by above con-
nection, please try to change the order of TXD
line and RXD line.
• Check baud rate:
If you need to check the baud rate.
Before powering on, set the baud rate to
115200 on your serial port test tool and
power on. When the RS232 serial of the product
connected to serial port test tool, the
software will read out the baud rate.
E.g.: The software shows information “ Baud rate:
9600”, and it means 9600 is the current baud rate.
• Set baud rate
For example, the current baud rate of extenders
are 9600, but the baud rate of control equipment
is 19200. In this case, choose baud rate 9600 for
serial port tool, then input command “set: 19200”
in character format and send it out. (set: xxxxx
have to send all at once in command line)
IR use guide
• IR passback
IR blaster cable should be pluged into the IR-out
of Transmitter, and the IR receiver cable should
be pluged into the IR-in port of the Receiver. The
emitter of IR blaster cable should be as close as
possible to the IR receiver window of the signal
source device.
• IR remote control
Using the IR remote controll to set/select the
channel of this HDMI Extender.
Button control
The left button controls the value of the left
Nixie tube, and the right one to control the value
of the right Nixie tube. When the value of “TX
connected” on the RX unit matches the value of
“TX ID” on the TX unit, the devices will pair/link
successfully.
Specyfikacje produktu
| Marka: | SIIG |
| Kategoria: | przedłużacz AV |
| Model: | CE-H23C11-S1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z SIIG CE-H23C11-S1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje przedłużacz AV SIIG
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
Instrukcje przedłużacz AV
- Alfatron
- Polycom
- Nedis
- StarTech.com
- SEADA
- IMG Stage Line
- Lindy
- Ecler
- PureLink
- AMX
- Adder
- Oehlbach
- Extron
- Blustream
- Intellinet
Najnowsze instrukcje dla przedłużacz AV
8 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
26 Lutego 2025
20 Lutego 2025
20 Lutego 2025
7 Lutego 2025