Instrukcja obsługi Soma Illuminator

Soma Niesklasyfikowane Illuminator

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Soma Illuminator (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 39 osób i została oceniona przez 20 użytkowników na średnio 4.8 gwiazdek

Pobierz PDF

Strona 1/2

Cut your LED strips and wires into their

desired lengths and connect them to-

gether and to the DC sockets supplied

with ILLUMINATOR.

• LEDstripshavespecialplaceswhere

you can cut the strip, usually they are

copper pads like in the photo below.

It’s important to cut the strip on the

middle line of these copper pads

• Youcansolderthewireeitherdirectly

to the copper pads or using ashort

wire that is often soldered to one or

both ends of the LED strip by the fac-

tory. Before soldering to the copper

padsyouneedremovethesiliconlayer

(ifpresent)coveringthepadsusing

asharp knife.

• Beawareofpolarity!Theplusand

minus on the LED strips are usually

marked by +

—

signs. The plus wire on

the speaker cable is usually marked by

aspecial color or line on one of the

wires. It doesn’t really matter which

of the two wires on the cable you use

for plus and minus. What matters is

that the plus of the LED strip is

connected to the central pin on

the DC jack. But don‘t worry. If you

mix up the polarity of the strip nothing

will be damaged, the strip just won’t

lightup.Inthiscasejusttrytoreverse

the polarity.

• Theconnectionbetweenthestripand

thewireshouldbecoveredinseveral

layers of isolation/electrical tape or

heatshrinktubing.Thisservestoboth

isolatetheconnectionandtogiveit

additional mechanical strength. In case

ofexcessivestress,thisistheplace

where the wire will likely be ripped from

the strip.

The strips are ready for use when all

of them are soldered to the wires, the

wires are soldered to the DC jacks and

all connections are insulated.

Now you need to choose aproper power

supply.YoucanbuyahighqualityPSU

from us (atan additional price) or use

aPSUthatyoualreadyhave.The PSU

must be 12V and the output DC jack

needs to be center plus. To calculate

the current your LED strips will need,

use the simple formula:

PSU max current in Ais equal or

more than total length of all LED

strips in meters x 0.3.

If your LED installation is not big, a1–2A

PSUcanbeenough.

If you use amodern switching mode

PSUyoudon‘tneedtoworryabout

overload.Allofthemhaveoverload

protection and will be shut down au-

tomaticallyiftheloadistoobig.Sono

ILLUMINATOR comes without LED strips,

wiresorPSU.Thereasonissimple

—

don‘t know what colors and length of

strips you need as well as what length

ofcables.Eachinstallationisveryper-

sonal and we can‘t supply something

thatcouldbecalled„auniversalsolu-

tion“.Youneedtoconnectthestrips

yourselfwhichrequiresbasicsoldering

skillsaswellassimplesolderingequip-

ment. Therefore, using ILLUMINATOR

requires some basic technical skills

and understanding.

First of all you need to buy LED strips

of desired length and color. You need

12V LED strips

Typically, one meter (3 feet) of aLED

strip consumes 0.2–0.35 ampere. We

recommend limiting the total length

of all LED strips connected to ILLU-

MINATOR to amaximum of 16 meters

(52 feet). Different strips connected to

differentchannelscanhavedifferent

lengths.

Secondly, you need to buy wire for

connecting LED strips to ILLUMINATOR.

We recommend standard speaker wire

used for audio speakers

. It’s import-

ant that the copper core is at least 0.35

squaremillimeters.0.5–1squaremilli-

meters is the optimal thickness.

OPERATION

MANUAL

1 2 3

Specyfikacje produktu

Marka:	Soma
Kategoria:	Niesklasyfikowane
Model:	Illuminator

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Soma Illuminator, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Niesklasyfikowane Soma

Soma Cosmos Instrukcja

14 Września 2024

Soma Ornament-8 Instrukcja

7 Września 2024

Soma Illuminator Instrukcja

6 Września 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

SmallRig VB99 SE Instrukcja

29 Stycznia 2025

Rock N Roller R14G Instrukcja

29 Stycznia 2025

Rock N Roller R6RT Instrukcja

29 Stycznia 2025

QSC TSC-8 Instrukcja

29 Stycznia 2025

XTRARM XTR-FS5130 Instrukcja

29 Stycznia 2025

Sunding SD-581G Instrukcja

29 Stycznia 2025

XTRARM XTR-FS5070 Instrukcja

29 Stycznia 2025

XTRARM XTR-FS2010 Instrukcja

29 Stycznia 2025

Shimbol Memory I PRO Instrukcja

29 Stycznia 2025

OSEE TX402 Instrukcja

29 Stycznia 2025