Instrukcja obsługi Sonneman Stix Plus 2794.03
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Sonneman Stix Plus 2794.03 (2 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/2
March 7, 2016
©2016 SONNEMAN - A WAY OF LIGHT 1 of 2
LED Product Information and Warnings
Important
• Always disconnect the power before installing or replacing bulbs and before cleaning or other maintenance.
• Consult a qualied, licensed electrician to ensure correct branch circuit conductor.
• Please read all included assembly instructions and warnings carefully before installation. Contact
Customer Service if you have any questions or concerns. Before installation, please conrm that the xture
is compatible with your supply voltage and dimming system, if present.
• LEDs are highly sensitive electronic devices, and must be treated with care. Do not open any factory
sealed compartments, and avoid touching the LEDs with your hands or any object.
• Although all our xtures are equipped with protective devices, LED xtures are vulnerable to power surges
and supply variations. Do not install LED xtures on the same circuit as any motors, appliances, or HVAC
systems.
• Do not remove or bypass any LED Driver or Transformer that is provided with the xture, and do not
replace or substitute with another power supply.
• Remote LED Driver or Transformer installation must be done by a licensed electrician and in accordance
with local codes. Remote installations should be in an accessible location, as close to the xture as possible.
• Fixtures must be wired in parallel on independent leads; do not "daisy chain" multiple xtures together or
wire them in series.
• All factory-made splices and connections must remain intact. LED circuits are carefully designed and built,
and improper connections may damage the xture.
• The ends of coaxial pendant cords have been precisely stripped and split at the factory and must not be
eld cut. Excess cord or cable should be neatly coiled and reserved in the xture canopy.
• Any mounting hardware is provided for your convenience and should be used with discretion. Always use
the appropriate hardware for the mounting surface.
March 7, 2016
©2016 SONNEMAN - A WAY OF LIGHT 2 of 2
Assembly Instructions
INSTRUCTIONS D’INSTALLATION
Stix Plus Series - 4ft. LED Wall Bar, 5ft. LED Wall Bar, 6ft. LED Wall Bar, 8ft. LED Wall Bar
Important
• Always disconnect the power before installing or replacing bulbs and before cleaning or other maintenance.
• Consult a qualied, licensed electrician to ensure correct branch circuit conductor.
Consulter un électricien qualié pour vous assurer que les conducteurs de la dérivation sont adéquats.
1. Shut o power to the branch circuit conductor.
2. The LED transformer (A) must be installed in a remote and accessible location near the xture in accordance with local
electrical code (Fig. 1). You must use the appropriate wire gauge from the transformer to the xture to limit the voltage drop
to less than 5%. Make appropriate electrical connections using wire nuts:
a. Connect the LED transformer’s live wire (black) to the live supply wire.
b. Connect the LED transformer’s neutral wire (white) to the neutral supply wire.
3. Drill a small hole (B) in the wall behind the xture (C) and pull the low voltage transformer output wires through the wall.
4. Make appropriate electrical connections using wire nuts: Connect one of the xture wires to one of the transformer output
wires. Connect the other xture wire to the second transformer output wire. Carefully push connections and extra wires
back through the hole (B) in the wall.
5. Remove diuser (D) from xture (C). Attach the xture to the wall with anchors (E) and screws (F) through the holes in the
xture. Snap the diuser back into the xture.
6. Restore power to the branch circuit conductor.
Note
• This xture is dimmable with Electronic Low Voltage (Trailing-Edge) type dimmers only.
Care Instructions
• Dusting: Use a clean, dry cloth.
• Cleaning: To protect the nish, avoid any harsh abrasives or chemicals.
2790, 2791, 2792, 2794
E
F
D
C
B
A
Fig. 1
Specyfikacje produktu
| Marka: | Sonneman |
| Kategoria: | Ulga |
| Model: | Stix Plus 2794.03 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Sonneman Stix Plus 2794.03, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ulga Sonneman
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
1 Stycznia 2025
1 Stycznia 2025
9 Października 2024
9 Października 2024
Instrukcje Ulga
- Ulga Delta Dore
- Ulga Goobay
- Ulga Eutrac
- Ulga Paul Neuhaus
- Ulga Peerless-AV
- Ulga Dometic
- Ulga Crivit
- Ulga Fysic
- Ulga Quasar Science
- Ulga ION
- Ulga LYYT
- Ulga MaxCom
- Ulga Livex Lighting
- Ulga Fuzzix
- Ulga Yongnuo
Najnowsze instrukcje dla Ulga
9 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
7 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025