Instrukcja obsługi SpeakerCraft IRE-1.0
SpeakerCraft
Zdalne sterowanie
IRE-1.0
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla SpeakerCraft IRE-1.0 (2 stron) w kategorii Zdalne sterowanie. Ta instrukcja była pomocna dla 20 osób i została oceniona przez 10.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/2
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,IRE-1.0 • LINEAR P/N: 223101X20 • INK: BLACK •
MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 17.500” FOLD TO 4.250” X 3.500”
• FOLDING: 5 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1
223101X20 • IMAGE 1
DESCRIPTION
The IRE-1.0 represents the highest level in sophistication for attachable
IR Emitters. It features a unique EZ-Docker
™ port that permits instant
removal of the emitter when rearranging or servicing components.
An improved adhesive reduces callbacks for reattachment of “fallen
emitters”. The case may also be taken apart so that the tiny internal
emitter can be placed inside a component, when desired. High IR
output from the top curved surface allows emitter to be mounted
on a nearby surface, below, above or on a cabinet door, rather than
directly on the sensor of the unit where conditions permit.
ATTACHMENT
First, locate the component’s IR sensor window and (see Note 1)
thoroughly clean it of any fingerprints or other greasy substances.
The EZ-Docker™ port has a clear adhesive layer on its bottom surface.
Peel the protective layer off,
exposing the adhesive.
Orient the port vertical (see
Fig. 2) and press it over the
center of the component’s
sensor window. Press and
hold for several seconds to
ensure maximum contact
of the adhesive.
Slide the emitter from the
top down, into the EZ-
Docker™ port. You should
feel it “snap” into place. (To
remove the emitter at any
time, simply push upward
until it “pops” out).
IRE-1.0
Emitter
8 FT 9/16"
7/16"
3.5mm
mini plug
1/4"
Side View
Emitter
Wire Lead
Docki ng
Port
Clear Adhe sive Tape
(See Note 3)
Top View
NOTE: White striped side is posit ive ( +)
(– )
(+ )
Emitter slides in to
Docki ng Port
TYPICAL INSTALLATION
Satellite Receiver
PS-1.0
IRE-1.0
IRE-1.0
Emitter
IRE-1.0
Emitter
VCR
A/V Receiver
Hand Held
Remote
IRC-3.0
Emitter
IR Sensor
Window
AT-1.0
Amplified Terminator
Unit
Power Supply
120V AC
(unswitched)
Shelf Top
IR Receiver
Fig. 1
Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft
Terminator or other source of IR (see Fig. 3)
.
CAUTION: Do not plug into an emitter jack that is set to Blaster
Power (BL ON) or to the HIGH OUT of other connecting blocks.
To do so will smoke the emitters!!
Note 1: If you have difficulty finding the component’s IR sensor, try
using a flashlight. Sometimes the owner’s manual is helpful. You may
need to contact the manufacturer direct.
Note 2: You may also attach the emitter without the EZ-Docker
™
port. Use one of the spare adhesives (included) applying it directly to
the bottom surface of the IRE-1.0 shell.
Note 3: If you need to remove the EZ-Docker™ port or emitter previ-
ously stuck to a component’s surface, use a fresh adhesive (included)
before reattaching.
Note 4: The emitter shell and EZ-Docker™
port, though dark in
appearance, are transparent to Infrared. This allows IR commands
to pass through them, permitting local hand held remote control as
well as through the IRE-1.0.
Fig. 3
IR Controlled Components
IR sensor
window
Docking Port
IRE-1.0 attached to
IR sensor window
2) Slide EmitterIRE-1.0
end into docking port
1) Attach Docking PortIRE-1.0
to IR sensor window with adhesive pad
Fig. 2
Specyfikacje produktu
| Marka: | SpeakerCraft |
| Kategoria: | Zdalne sterowanie |
| Model: | IRE-1.0 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z SpeakerCraft IRE-1.0, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Zdalne sterowanie SpeakerCraft
20 Września 2024
Instrukcje Zdalne sterowanie
- Genaray
- Archos
- Zalman
- Sony
- TV Vlaanderen
- Axis
- Valueline
- Vision
- Gaggenau
- Edision
- Vello
- Control4
- DJI
- Universal Remote Control
- TechniSat
Najnowsze instrukcje dla Zdalne sterowanie
9 Kwietnia 2025
6 Kwietnia 2025
6 Kwietnia 2025
4 Kwietnia 2025
2 Kwietnia 2025
1 Kwietnia 2025
1 Kwietnia 2025
31 Marca 2025
31 Marca 2025
30 Marca 2025