Instrukcja obsługi Speco Technologies HTINT70TA
Speco Technologies
kamera wideo
HTINT70TA
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies HTINT70TA (2 stron) w kategorii kamera wideo. Ta instrukcja była pomocna dla 39 osób i została oceniona przez 20 użytkowników na średnio 5.0 gwiazdek
Strona 1/2
HD-TVI 2MP Intensier® Bullet Camera
QUICK INSTALLATION GUIDE
Special features
Sony 1/2.9 inch 2.1MP Exmor CMOS Sensor
2.7 ~ 12mm Motorized Zoom & Focus Control
Supports image resolution up to 1920 x 1080P 30fps @
Wide Dynamic Range (15fps)
Full OSD operation through on-board control and UTC
2D & 3D noise reduction
SENS- (Digital Slow Shutter) UP
Privacy masking (16zone)
Dynamic Motion Detection (4zone)
Defog
Surge Protect (DC 2KV / Video 3 KV)
DEAR CUSTOMERS!
By selecting this product, you have decided to use a professional device that
guarantees highest quality and reliability. We would like to thank you very much for
your condence and kindly ask you to read the following instructions carefully before
installation and operation in order to take full advantage of all quality features
regarding this product.
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
WARNING
Changes or modications not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.
CAUTION –To prevent electric shock and risk of the re hazards
Do NOT use power source other than that specied.
Do NOT expose this appliance to rain or moisture.
1. Precautions
Please read the manual carefully before the installation in order to make use the
camera to be set up correctly and to have the best picture quality.
Please keep the manual in good condition for your future reference and service
application.
Installation and services should only be carried out by an authorized personnel
according to local safety regulations.
If any liquid or solid matter gets into the housing, immediately disconnect the camera
from power supply and have it checked by your authorized dealer before reusing.
Avoid installing the camera at extremely hot or cold places.
If you are not a certied person, never try to dismantle the camera.
To avoid electric shock, never remove the screws or covers. There are no parts inside
that need maintenance by the user. All maintenance should be carried out by qualied
personnel.
Avoid installing the camera at a place of high humidity.
Avoid installing the camera at the place exposed to gas or oil.
Keep the top glass of the lens always clean in order to obtain the best picture quality
all the time. Be careful not to be stained by ngerprint.
Don't face the camera directly toward sunlight or sunlight reecting area.
CMOS may go defective at this condition.
Please give a special attention to keep the unit from dangerous drop or external shock
during the process of transportation or handling.
Never try to touch the camera in wet hand. It may cause an electric shock.
Do not expose the camera to radioactivity. It causes a serious damage on the CMOS.
2. Limitation of liability
This publication is provided “AS IS” without warranty of any kind, either express or
implied, including but not limited to, the implied warranties of merchantability, tness for
any particular purpose, or non-infringement of the third party's right.
This publication could include technical inaccuracies or typographical errors.
Changes are added to the information herein, at any time, for the improvements of this
publication and / or the corresponding product(s).
3. Disclaimer of warranty
In no event shall seller be liable to any party or any person, except for replacement or
reasonable maintenance of the product, for the cases, including but not limited to below :
(1) Any damage and loss, including without limitation, direct or indirect, special,
consequential or exemplary, arising out of or relating to the product.
(2) Personal injury or any damage caused by inappropriate use or negligent operation of
the user.
(3) Unauthorized disassemble, repair or modication of the product by the user.
(4) Inconvenience or any loss arising when images are not displayed, due to any reason
or cause including any failure or problem of the product.
(5) Any problem, consequential inconvenience, or loss or damage, arising out of the
system combined by the devices of third party.
(6) Any claim or action for damages, brought by any person or organization being
photogenic subject, due to violation of privacy with the result of that surveillance-
camera's picture, including saved data, for some reason, becomes public or is used
for the purpose other than surveillance.
4. Package
4. Package
- Junction Box
5. Installation
5-1. How to install on the Wall
Wall_Junction Box
Wall
① Drill four screw holes on the wall plate to x four plastic anchors (supplied) in the holes.
② Fix the plastic anchors in the holes.
③ Position the bracket on the screw points.
④ Fix the bracket by tightening the screws.
5- OSD cap detailed description 2.
Open the Closing Cap and fasten the Closing Cap well.
The lighting ash with an arrowhead symbol, within an equilateral triangle
is intended to alert the user to the presence of non-insulated dangerous
voltage within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
This installation should be made by a qualied service person and should conform to
all local codes.
CAUTION
TO REDUCE THE RISK OF ELECTRLC SHOCK,
DO NOT REMOVE THE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED PERSONNEL.
RISK OF ELECTRLC
SHOCK
DO NOT OPEN
CAUTION
HTINT70TA
Screw PH
M4 x 0.47in (4EA)
Tapping screw
Ø 4 x 1.18in (4EA)
Plastic anchor
(4EA)
Camera x 1
Manual x 1
Tapping screws x 4
Plastic anchor x 4
L-Wrench ( 16in) x 1 0.
L-Wrench ( in) x 1 0.10
Top Rubber x 1
Junction Box x 1
Sponge x1
Screw PH
(M4 x 0.47in) x 4
Tapping Screws
(Ø 4 x 1.18in) x 4
Plastic Anchor x 4
Tool-free 3-Axis
IP67 Weatherproof
12VDC / 24VAC Dual Input
Built-in Heater
Closing Cap
F/W Writing Pin
OSD Switch
CVBS
L-Wrench (0.10in)
Closing Cap Open
Specyfikacje produktu
| Marka: | Speco Technologies |
| Kategoria: | kamera wideo |
| Model: | HTINT70TA |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Speco Technologies HTINT70TA, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje kamera wideo Speco Technologies
15 Września 2024
15 Września 2024
15 Września 2024
14 Września 2024
14 Września 2024
13 Września 2024
13 Września 2024
13 Września 2024
12 Września 2024
12 Września 2024
Instrukcje kamera wideo
- Kenwood
- Whistler
- Steinberg
- Replay
- Nikon
- Rexing
- Hazet
- Contax
- Creative
- Macally
- BlackVue
- Leica
- Thinkware
- EE
- IOPLEE
Najnowsze instrukcje dla kamera wideo
30 Marca 2025
30 Marca 2025
30 Marca 2025
30 Marca 2025
28 Marca 2025
28 Marca 2025
28 Marca 2025
27 Marca 2025
14 Marca 2025
12 Marca 2025