Instrukcja obsługi Speco Technologies O4P25X2
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies O4P25X2 (65 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 7.5 użytkowników na średnio 4.6 gwiazdek
Strona 1/65
User Manual
PTZ Network Camera
O4P25X2
Please read this instruction carefully before operang the unit keep it for further reference and
1. Electrical safety
All installaon and operaon here should conform to local electrical safety codes.
Use a certied/listed 24VDC/AC (depending on models) Class2 or adequate PoE switch.
Improper handling and/or installaon could run the risk of re or electrical shock.
2. Environment
Do not expose the heavy stress, violent vibraon long-term exposure water humidity during transportaon, unit to or to and
storage, and/or installaon.
Do not install near rces heat. sou of
Only install the product environments inside the specicaon operating temperature in and humidity range.
Do not install the camera near power lines, radar equipment other electromagnec radiaon. or
Do not block any venlaon openings any. if
Use all the weatherproong hardware requirement minimize weather intrusion.to
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface.
Always use the dry so cloth to clean the device. If there is too much dust, use a cloth dampened with a small quanty of neutral
detergent. Finally use the dry cloth to clean the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may
result in poor IR funconality and/or IR reecon.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an opcal device, please do not touch or wipe cover surface directly during installaon and use, please refer to the
following methods if dirt is found.
Stained with dirt:
Use oil-free so brush or hair dryer to remove it gently.
Stained with grease or ngerprint.
Use oil-free coon cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and
wipe several mes if it is not clean enough.
Warning
This camera should be installed by qualied personnel only.
All the examination and repair work should be done by qualied personnel.
Any unauthorized changes or modicaons could void the warranty.
Statement
This guide is for reference only.
Product, manuals, and specicaons may be modied without prior noce. Speco Technologies reserves the right to modify these
without noce and without incurring any obligaon.
Speco Technologies is not liable for any loss caused by improper operation.
Regulatory Informaon
FCC condions:
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operaon.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protecon against harmful interference. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause harmful
interference to radio communicaon. However, there is no guarantee that interference will not occur in a parcular installaon. If
this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Note:
Before installaon, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the package.
Specyfikacje produktu
| Marka: | Speco Technologies |
| Kategoria: | Kamera monitorująca |
| Model: | O4P25X2 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Speco Technologies O4P25X2, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kamera monitorująca Speco Technologies
12 Stycznia 2025
12 Stycznia 2025
11 Stycznia 2025
22 Września 2024
20 Września 2024
20 Września 2024
18 Września 2024
18 Września 2024
18 Września 2024
18 Września 2024
Instrukcje Kamera monitorująca
- Kamera monitorująca Linear PRO Access
- Kamera monitorująca SMC
- Kamera monitorująca Lorex
- Kamera monitorująca Konig
- Kamera monitorująca Brilliant
- Kamera monitorująca Oplink
- Kamera monitorująca Securetech
- Kamera monitorująca POSline
- Kamera monitorująca Owltron
- Kamera monitorująca Zavio
- Kamera monitorująca M-e
- Kamera monitorująca Xavax
- Kamera monitorująca Laserliner
- Kamera monitorująca Illustra
- Kamera monitorująca ION
Najnowsze instrukcje dla Kamera monitorująca
28 Stycznia 2025
25 Stycznia 2025
17 Stycznia 2025
17 Stycznia 2025
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
12 Stycznia 2025