Instrukcja obsługi Speco Technologies O8B7M
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies O8B7M (54 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 4.8 gwiazdek
Strona 1/54
User Manual
8MP IP Camera
O /O 8B7M 8D7M
Please read this instrucon carefully before operang the unit and keep it for further reference
Important Safeguards and Warnings
1. Electrical safety
All installaon and operaon here should conform to local electrical safety codes.
Use a cered/listed 12VDC Class2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same me; it may result in device damage! The
product must be grounded to reduce the risk of electric shock.
Improper handling and/or installaon could run the risk of re or electrical shock.
2. Environment
Heavy stress, violent vibraon or exposure to water is not allowed during transportaon, storage and installaon.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature condions.
Do not expose the camera to electromagnec radiaon. Otherwise it may result in CMOS sensor failure.
Do not block any venlaon openings.
Do not allow water and liquid intrusion into the camera.
3. Operaon and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor opc component. You can use a blower to clean the dust on the lens surface.
Always use the dry so cloth to clean the device. If there is too much dust, use a cloth dampened with a small quanty of neutral
detergent. Finally use the dry cloth to clean the device.
Please use a professional opcal cleaning method to clean the enclosure. Improper enclosure cleaning (such as using cloth) may
result in poor IR funconality and/or IR reecon.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an opcal device, please don t touch or wipe cover surface directly during installaon and use, please refer to the ’
following methods if dirt is found.
Stained with dirt:
Use oil-free so brush or hair dryer to remove it gently.
Stained with grease or ngerprint
Use oil-free coon cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and
wipe several mes if it is not clean enough.
Warning
This camera should be installed by qualied personnel only.
All the examinaon and repair work should be done by qualied personnel.
Any unauthorized changes or modicaons could void the warranty.
Statement
This guide is for reference only.
Product, manuals and specicaons may be modied without prior noce. Speco Technologies reserves the right to modify these
without noce and without incurring any obligaon.
Speco Technologies is not liable for any loss caused by improper operaon.
Regulatory Information
FCC condions:
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operaon.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protecon against harmful interference. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instrucon manual, may cause harmful
interference to radio communicaon. However, there is no guarantee that interference will not occur in a parcular installaon. If
this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Note:
Before installaon, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is broken or missing in the package.
Accessory name
Amount
Network Camera Unit
1
Juncon box
1
Quick Start Guide
1
Installaon Accessories Bag
1
CD
1
Specyfikacje produktu
| Marka: | Speco Technologies |
| Kategoria: | Kamera monitorująca |
| Model: | O8B7M |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Speco Technologies O8B7M, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kamera monitorująca Speco Technologies
12 Stycznia 2025
12 Stycznia 2025
11 Stycznia 2025
22 Września 2024
20 Września 2024
20 Września 2024
18 Września 2024
18 Września 2024
18 Września 2024
18 Września 2024
Instrukcje Kamera monitorująca
- Kamera monitorująca Ikegami
- Kamera monitorująca Ganz
- Kamera monitorująca EZVIZ
- Kamera monitorująca Ebode
- Kamera monitorująca Manhattan
- Kamera monitorująca AG Neovo
- Kamera monitorująca Schwaiger
- Kamera monitorująca Linksys
- Kamera monitorująca LevelOne
- Kamera monitorująca Security Labs
- Kamera monitorująca Topica
- Kamera monitorująca POSline
- Kamera monitorująca BIRDFY
- Kamera monitorująca Videotec
- Kamera monitorująca Inkovideo
Najnowsze instrukcje dla Kamera monitorująca
28 Stycznia 2025
25 Stycznia 2025
17 Stycznia 2025
17 Stycznia 2025
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
12 Stycznia 2025