Instrukcja obsługi Speco Technologies O8VLB3
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Speco Technologies O8VLB3 (10 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 4 użytkowników na średnio 4.3 gwiazdek
Strona 1/10
Quick Start Guide
8 MP Bullet IP Camera
O8VLB3
V 1.0
i
Welcome
Thank you for purchasing this network camera!
Please read this manual carefully before operang the unit and retain it for future reference.
Should you require any technical assistance, please contact Speco Technologies Technical Support.
Important Safeguards and Warnings
1 Electrical safety
．
．
．
．．
All installaon and operaon here should conform to local electrical safety codes.
Use a certied/listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same me; it may result in device
damage! The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installaon could run the risk of re or electrical shock.
2 Environment
．
．
．
．．
Heavy stress, violent vibraon or exposure to water is not allowed during transportation, storage and installaon.
This product should be installed in a cool, dry place away from direct sunlight and heat sources.
Do not install the product in extreme temperature condions.
Do not expose the camera to electromagnec radiaon. Otherwise it may result in CMOS sensor failure.
Do not block any venlation openings.
Do not allow water and liquid intrusion into the camera.
3. Operaon and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work.
Do not touch the CMOS sensor opc component. You can use a blower to clean the dust on the lens surface.
Always use the dry so cloth to clean the device. If there is too much dust, use a cloth dampened with a small
quanty of neutral detergent. Finally use the dry cloth to clean the device.
Please use a professional opcal cleaning method to clean the enclosure. Improper enclosure cleaning (such as using
cloth) may result in a poor image.
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera.
Dome cover is an opcal device, please don’t touch or wipe cover surface directly during installaon and use, please
refer to the following methods if dirt is found:
Stained with dirt
Use oil-free so brush or hair dryer to remove it gently.
Stained with grease or ngerprint
Use oil-free coon cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the
cloth and wipe several times if it is not clean enough.
ii
Warning
This camera should be installed by qualied personnel only.
All the examinaon and repair work should be done by qualied personnel.
Any unauthorized changes or modicaons could void the warranty.
Statement
This guide is for reference only.
Product, manuals and specicaons may be modied without prior noce. Speco Technologies reserves the right to
modify these without noce and without incurring any obligaon.
Speco Technologies is not liable for any loss caused by improper operaon.
Regulatory Informaon
1.1 FCC condions：
：
：
：：
This device complies with part 15 of the FCC Rules. Operaon is subject to the following two conditions:
This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operaon.
1.2 FCC compliance：
：
：
：：
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference. This equipment
generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucon
manual, may cause harmful interference to radio communicaon. However, there is no guarantee that interference
will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separaon between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Note
Please refer to the disk for more details, check and download the corresponding user’s manual and tool.
Before installaon, please open the package and check all the components are included.
Contact your local retailer as soon as possible if something is broken in your package.
Accessory Name
Amount
Accessory Name
Amount
Network Camera
1
Installaon Position
Map
1
Quick Start Guide
1
Waterproof
Connector
1
Screw Package
1
CD
1
Wrench
1
-
-
Specyfikacje produktu
| Marka: | Speco Technologies |
| Kategoria: | Kamera monitorująca |
| Model: | O8VLB3 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Speco Technologies O8VLB3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Kamera monitorująca Speco Technologies
12 Stycznia 2025
12 Stycznia 2025
11 Stycznia 2025
22 Września 2024
20 Września 2024
20 Września 2024
18 Września 2024
18 Września 2024
18 Września 2024
18 Września 2024
Instrukcje Kamera monitorująca
- Kamera monitorująca Caddx
- Kamera monitorująca Whistler
- Kamera monitorująca Trevi
- Kamera monitorująca BZBGear
- Kamera monitorująca Motorola
- Kamera monitorująca I-PRO
- Kamera monitorująca NetMedia
- Kamera monitorująca JUNG
- Kamera monitorująca Aqara
- Kamera monitorująca Cisco
- Kamera monitorująca E-bench
- Kamera monitorująca Axis
- Kamera monitorująca Inkovideo
- Kamera monitorująca Y-cam
- Kamera monitorująca Reolink
Najnowsze instrukcje dla Kamera monitorująca
28 Stycznia 2025
25 Stycznia 2025
17 Stycznia 2025
17 Stycznia 2025
15 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
13 Stycznia 2025
12 Stycznia 2025
12 Stycznia 2025