Instrukcja obsługi Supermicro A+ Server 2024US-TRT

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Supermicro A+ Server 2024US-TRT (1 stron) w kategorii serwer. Ta instrukcja była pomocna dla 36 osób i została oceniona przez 2 użytkowników na średnio 4.3 gwiazdek

11 10 9

http://www.supermicro.comMNL-2315-QRGRev. 1.0a

SuperServer AS -2024US-TRT Quick Reference Guide

Front View & InterfaceRear View

Hard Drive Installation

Board Layout

Remov aing

Hot-Swap Drive Carrier from the

Chassis

1. Press the release button on the drive carrier, which will extend the

drive carrier handle.

2. Use the drive carrier handle to pull the drive out of the chassis.

Insta a Drivelling

1. Remove the dummy drive, by removing the screws securing the dummy drive to

the carrier. These screws are not used to mount the actual hard drive.

2. Insert a drive into the carrier with the PCB side facing down and the connector

end toward the rear of the carrier. Align the drive in the carrier so that the screw

holes line up.

3. Secure the drive to the carrier with four M3 screws, included in the chassis

accessory box.

4. Insert the drive carrier with the disk drive into its bay, keeping the carrier oriented

so that the release button is on the right side. When the carrier reaches the rear of

the bay, the release handle retracts.

5. Push the handle in until it clicks into its locked position.

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning before

connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment, disconnect power

from server by disconnecting all power cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap.

WARNING:

Always be sure all power supplies for this system have the same power

output. If mixed power supplies are installed, the system will not operate.

For more information go to : http://www.supermicro.com/support



!



!



!

1. Removing the Processor Force Frame

Use a Torx T20 driver to loosen the screws holding

down Force Frame in the sequence of . The 3-2-1

screware numbered on the Force Frame next teach s o

screw hole.

2. Raising the Force Frame3. Lifting the Rail Frame

5. Inserting the Carrier Frame/CPU Package6. Lowering the Force Frame7. Securing the Force Frame

Secure the screws in the order 1-2-3, tightening to

16.1 kgf-cm (14 lbf-in) of torque. The Force Frame

secures both the Rail Frame and CPU Package.

Caution: Tightening must be executed in proper

1-2-3 sequence to avoid causing catastrophic

damage to the socket or CPU Package.

8. The Force Frame Secured

Screw #1

Screw #2

Screw #3

Force Frame

Rail Frame

PnP Cover Cap

Carrier Frame/

CPU Package

Processor Installation

4. Removing the External Cap and PnP

Cover Cap

External Cap

PnP Cover Cap

Heatsink Installation

DescriptionNo.

1

2

3

4

5

6

7

8

9

PCI-E p1-x16 Slot (FH, 9.5” L)

PCI-E p1-x16 Slot (FH, 10.5” L)

VGA Port

UID LED

Serial Port

Dedicated LAN for IPMI

Two USB 3.0 Ports

Two 10G RJ45 Ports (Ultra Riser Card)

PCI-E p1-x16 Slot (LP)

10 PCI-E p1-x8 in p1-x16 Slot (FH, 10.5” L)

11 PCI-E p1-x16 Slot (FH, 10.5” L)

*Redundancy based on configuration and application load

Memory

DIMM Module Population Sequence

When installing memory modules, the DIMM slots should be populated in the following order:

DIMMA2, DIMMB2, DIMMC2, DIMMD2, DIMME2, DIMMF2, DIMMG2, DIMMH2, then DIMMA1,

DIMMB1, DIMMC1, DIMMD1, DIMME1, DIMMF1, DIMMG1, DIMMH1.

• The blue slots must be populated first.

• Always use DDR4 DIMM modules of the same type, size and speed.

• d DIMM s n be std. er, l DIs MixespeedcainalleHowevalMMwilrul n athe d ot speef stthe eslow DIMM.

• The motherboard will support odd-numbered modules (1 or 3 modules installed).

However, to achieve the best memory performance, fully populate the motherboard with validated

memory modules.

* Optnal NVMeio Support (HDD0 a 1 from CPU1, a 3 from CPU2)ndHDD2nd

1

2

HDD2

HDD1

HDD0

HDD5

HDD4

HDD3

HDD8

*

HDD7

HDD6

HDD11

*

HDD10

*

HDD9

*

3

4

7

6

58

9

10

12

RESET

Dummy Drive

Hard Drive Carrier

3

+

DESIGNED IN USA

H12DSU-iN

REV:

1 2

8

9

10

6

4 5

6

11 12 13 1415 16

7

No.tnDescrip io

1SXB11: -L s St P PCI-E 4.0 )A/B/1CWIORierCarduppor(CU2x32

2SXB2: St P PCI-E 4.0 x)WIO-RRiser Carduppor(CU216

3SXB33: t St P PCI-E 4.0 )A/B/3CUlraI/O RiserCarduppor(CU1x40

4CPU1 NV0- SA7Me Ports 1,AT0-

5SAAT DOM 3.0 98-

6CPU2 NV SA3Me Port 0,AT10-1

7CPU2 VNMe Port 1, SAAT14-17

8CPU1 NV3Me Ports 2-

9CPU2 NV3Me Ports 2-

10 JBT1 - CMOS Clear

11 CPU2 DIA StsMM1-D2lo

12 CPU2

13 CPU2 DIE otsMM1-H2Sl

14 CPU1 DIA StsMM1-D2lo

15 CPU1

16 CPU1 DIE StsMM1-H2lo

Proo a Their Co o MescessrsndrrespondingMemryodul

CPU# Chael nn

1Chael nn

2Chael nn

3Chael nn

4Chael nn

5Chael nn

6Chael nn

7Chael nn

8

8 DISMM

CPU1 C2 D2G2 H2

CPU2 C2 D2G2 H2

16MM DIS

CPU1 A2 B2C2D2 E2 F2 G2H2

CPU2 A2 B2C2D2 E2 F2 G2H2

32MM DIS

CPU1 A1 A2B1 B2 C1 C2 D1D2 E1 E2F1F2 G1G2H1H2

CPU2 A1 A2B1 B2 C1 C2D1 D2 E1 E2F1F2 G1G2 H1H2

JL1

JF1

FAN7

FAN8JF2

P2-DIMMA1

P2-DIMMB1

P2-DIMMA2

P2-DIMMC1

P2-DIMMB2

P2-DIMMD2

P2-DIMMD1

P2-DIMMC2

JVR1

FAN3

FAN4

FAN5

FAN6

P2-DIMMH2

P2-DIMMG2

P2-DIMMH1

P2-DIMMF2

P2-DIMMG1

P2-DIMME2

P2-DIMMF1

P2-DIMME1

P1-DIMMD2

P1-DIMMC2

P1-DIMMC1

P1-DIMMD1

P1-DIMMA1

P1-DIMMA2

P1-DIMMB1

P1-DIMMB2

CPU1CPU2

P1-DIMMG1

P1-DIMMG2

P1-DIMMH1

P1-DIMMF2

P1-DIMMF1

P1-DIMME2

P1-DIMME1

P1-DIMMH2 FAN1

FAN2

LE1

CPU Installation

Hard Drive Signal

Hard Drive Fail

Power Button

Reset Button

NIC1 LED

Information LED

Power LED

NIC2 LED

DescriptionNo.

1

2

3

4

6

7

8

9

HDD Activity LED

Power Fail LED

5

10

83

6

745

12 1

Default Cable Routing

Cor on onnect

Bodar Card/Cn onnioect

Backplane HDDBaMCCa yS blP/e N

JSLIM1

(M -H12D U-iNBS)CN1CN0-L-, 27CBSAST-1253-100

JSLI 2M3-

(M -H12D U-iNBS)CN8-311CBTL-SAS -1269-10F0

JSLIM2

(M -H12D U-iNBS)NV 1Me0-1

(Hybridwi th SA)ATCBTL-SAS -1247-85

JSLIM4

(M -H12D U-iNBS)NV 2Me2-3

(Hybridwi th SA)ATCBTL-SAS -1245-85

2

1

Redundant Power Supply Modules*

12

Removing a Drive Carrier

Release Button

1. Mounting the Heatsink2. curing the HeatsinkSe

Using a diagonal pattern and a Torx T20 driver,

tighten the four heatsink screws evenly to 16.1

kgf-cm (14.0 lbf-in) torque.

#4cre Sw

#2cre Sw

#1cre Sw

#3cre Sw

Specyfikacje produktu