Instrukcja obsługi Supermicro SuperServer 2028TP-DTTR

Supermicro serwer SuperServer 2028TP-DTTR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Supermicro SuperServer 2028TP-DTTR (1 stron) w kategorii serwer. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 4.5 użytkowników na średnio 4.6 gwiazdek

Pobierz PDF

Strona 1/1

http://www.supermicro.com MNL-1657-QRG

Board Layout

SuperServer 2028TP-DTR/DTTR/DTFR Quick Reference Guide

Rear View

BIOS Beep Codes

Beep Code/LED Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long

beep

Memory Error

5 beeps and 2 short

beeps

Display memory

read/write error

CPU Installation

Beep Codes

Front view & Interface



Heatsink Installation

1. Place the heatsink on top of the installed CPU.

2. Align the four screws to the socket.

3. Holding the heatsink in place, screw down as shown

(cross pattern, in order: A, C, B, D).

4. Note: Only use 6-8 lb/f of torque; otherwise, hand-tighten

each screw to avoid damaging the CPU.

Memory

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

Align CPU to socket;

install CPU straight down

For more information go to :

http://www.supermicro.com/support



No memory detected

NOTE:

Do not bend pin inside socket



Processors and Memory Module Population for Optimal Performance

Number of

CPUs + DIMMs

CPU and Memory Population Configuration Table

(For memory to work properly, follow the instructions below)

1 CPU & 2 DIMMs CPU1: P1-DIMMA1/P1-DIMMB1

1 CPU & 4 DIMMs

1 CPU & 5~8 DIMMs

2 CPUs & 4 DIMMs

2 CPUs & 6 DIMMs

CPU1: P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

CPU1: P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 +

Any memory pairs in P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slot

CPU1 + CPU2: P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

CPU1 + CPU2: P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs & 8 DIMMs

2 CPUs &

8~16 DIMMs

2 CPUs &

16 DIMMs

CPU1 + CPU2: P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1

+ Any memory pairs in P1, P2 DIMM slots

CPU1 + CPU2: P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIMMG1/P2-DIMMH1,

P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/P2-DIMMF2/P2-DIMMG2/P2-DIMMH2

Processors and their Corresponding Memory Modules

CPU# Corresponding DIMM Modules

CPU 1 P1-DIMMA1

CPU 2 P2-DIMME1

P1-DIMMB1

P2-DIMMF1

P1-DIMMC1

P2-DIMMG1

P1-DIMMD1

P2-DIMMH1

P1-DIMMA2

P2-DIMME2

P1-DIMMB2

P2-DIMMF2

P1-DIMMC2

P2-DIMMG2

P1-DIMMD2

P2-DIMMH2

Nodes and Corresponding Hard Drives

Hard Drive Signal

Hard Drive Fail

Power Button

LAN LED

Alert

UID Button

Description

No.

Description

No.

DescriptionNo.

SXB1: S-SATA 0-2/PCI-E 3.0 p1-x16 Slot supported by CPU2

P2-DIMME1/P2-DIMME2 slot

P2-DIMMF1/P2-DIMMF2 slot

Slot1: CPU2 Slot1 PCI-E 3.0 x16

JBT1: CMOS Clear

Slot2: CPU2 Slot2 PCI-E 3.0 x8

CPU2

InfiniBand (FDR) Connector (2028TP-DTFR only)

Gigabit LAN1/LAN2 or 10G Base-T Connector (2028TP-DTTR only)

S-SATA3: SATA DOM (Disk_On_Module) with Power-pin Connector

JSD1: SATA DOM (Device_on_Module) Power Connector

P2-DIMMH1/P2-DIMMH2 slot

P2-DIMMG1/P1-DIMMG2 slot

P1-DIMMA1/P1-DIMMA2 slot

P1-DIMMB1/P1-DIMMB2 slot

CPU1 (Install CPU1 first)

P1-DIMMC1/P1-DIMMC2 slot

P1-DIMMD1/P1-DIMMD2 slot

SXB2: I-SATA 0-5/PCI-E 3.0 p1-x8 Slot supported by CPU1

0 Slot

Low-Profile PCI-E Slot (1x16 & 1x8)

VGA Connector

InfiniBand Port (2028TP-DTFR only)

G_LAN or 10G Base-T Connector (2028TP-DTTR only)

USB Ports

IPMI LAN Port

Power Supply Module

Video adapter missing or with faulty

memory

1 continuous beep System Overheat System Overheat

JBT1

P1-DIMMB2

S-SATA3

COM1

JIPMB1

FAN3

FAN4

JSD1

JTPM1

JF1

UID_LED1

BMC_HB_LED1

JPG1

JPB1

JVRM2

JVRM1

JWD1

JPL1

/CPU2 PCI-E 3.0 X16)

(CPU2 SLOT1 PCI-E 3.0 X16)

PCI-E 3.0 X8)(CPU2 SLOT2

UID SW

BATTERY

BIOS

BMC

QSFP

LAN1/LAN2

10G/1G

(3.0)USB0/1

IPMI_LAN

SATA DOM+POWER

TPM/PORT80

CPU2 VRM_HS1

CPLD

P2-DIMMG1

P2-DIMMH2

P2-DIMMH1

P2-DIMMG2

P2-DIMMF2

P2-DIMME1

P2-DIMME 2

P2-DIMMF1

P1-DIMMD2

P1-DIMMD1

P1-DIMMC2

P1-DIMMC1

P1-DIMMB1

P1-DIMMA2

P1-DIMMA1

/CPU1PCI-E 3.0 X8)(I-SATA0~5

CPU2

CPU1

LAN CTRL

PCH

IB_LINK LED1

IB_ACT_LED1

(S-SATA0~2

SXB1 SXB2

Slot1 Slot2

X10DRT-P Series

Rev. 1.02

1516171819

VGA

SXB1

SXB2

5 6 7 8 119 10

P t g I / IMM y es opula in RD MM LRD Memor Modul

In Suppote 5-2600v er cess Meml E 3 S ies Pro or ory rt

Type Ranks

Per

DIMM

& Data

Width

DIMM

Capacity (GB)

Speed (MT/s), Voltage (V), Slot per Channel

(SPC) and DIMM Per Channel (DPC)

1 Slot Per

Channel

2 Slots Per Channel

1DPC 1DPC 2DPC

4Gb 8Gb 1.2V 1.2V 1.2V

RDIMM SRx4 8GB 16GB 2133 MHz 2133 MHz 1866 MHz

RDIMM SRx8 4GB 8GB 2133 MHz 2133 MHz 1866 MHz

RDIMM DRx8 8GB 16GB 2133 MHz 2133 MHz 1866 MHz

RDIMM DRx4 16GB 32GB 2133 MHz 2133 MHz 1866 MHz

LRDIMM QRx4 32GB 64GB 2133 MHz 2133 MHz 2133 MHz

6 45

8 7

S d w s the Ch iserver arbo Dra er Lo ioncat in ass

Serverboard A

Controls HDDs A1 through A12

Serverboard B

Controls HDDs B1 through B12

Screw #D

Screw #A

Screw #C

Screw #B

ID tag

ÌMNL-1657-QRG7Î

Note:

1. Install CPU1 first.

2. In order to support PCI-e and Zero slots, two CPUs must be installed.

Specyfikacje produktu

Marka:	Supermicro
Kategoria:	serwer
Model:	SuperServer 2028TP-DTTR
Kolor produktu:	Czarny
Wysokość produktu:	88 mm
Szerokość produktu:	438 mm
Głębokość produktu:	724 mm
Bluetooth:	Nie
Certyfikaty:	RoHS
Ilość portów Ethernet LAN (RJ-45):	6
Zakres temperatur (eksploatacja):	10 - 35 °C
Zakres wilgotności względnej:	8 - 90 %
Wi-Fi:	Nie
Przewodowa sieć LAN:	Tak
Zintegrowany czytnik kart:	Nie
Waga wraz z opakowaniem:	38600 g
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-40 - 70 °C
Dopuszczalna wilgotność względna:	5 - 95 %
Ilość obsługiwanych rozmiarów dysków pamięci:	16
Interfejs napędów pamięci masowej:	Serial ATA III
Obsługiwane rozmiary dysków pamięci:	2.5 "
Ilość portów USB 3.2 Gen 1 (3.1 Gen 1) Typu-A:	4
Obudowa:	Rack (2U), -
Obsługiwane rodzaje pamięci:	DDR4-SDRAM
Liczba gniazd pamięci:	16
Obsługiwane prędkości zegara pamięci:	1600,1866,2133 MHz
Maksymalna pojemność pamięci:	1000 GB
Gniazdo procesora:	LGA 2011 (Socket R)
Procesor:	Intel® Xeon®
Układ płyty głównej:	Intel® C612
Poziomy raid:	0, 1,5, 10
Typ BIOS:	AMI
PCI Express x16 gniazda:	4
Zasilanie:	100 - 240V, 50-60Hz
Kontroler LAN:	Intel X540, Realtek RTL8201N
Wbudowana kamera/aparat:	Nie
Liczba portów VGA (D-Sub):	2
Cechy sieci:	10GBase-T LAN
Rodzina adaptera graficznego:	Aspeed
Wskaźnik LED zasilania:	Tak
Korekcja ECC:	Tak
Karta graficzna on-board:	Tak
Model karty graficznej on-board:	Aspeed AST2400
Szeregowe porty komunikacyjne:	2
Wsparcie wentylatorów nadmiarowych:	Tak
Napędy optyczne:	Nie
Ilość gniazd SATA:	16
PCI Express x8 slots:	2