Instrukcja obsługi Tado Wireless Temperature Sensor
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tado Wireless Temperature Sensor (8 stron) w kategorii termostat. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 8.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/8
Manual for Professional
Installers
DIY Installation
If you are a professional installer, please not download the tado˚ app. There you will find specific installation instructions.
This manual is meant exclusively for professional installers. It includes generic instructions to install the Wireless
Receiver (Programmer) and the Wireless Temperature Sensor.
For the Starter Kit - Wireless Smart Thermostat V3+
(Incl. Programmer with Hot Water Control)
Manual version 3.2
A. Remove the battery
protection strip.
B. Press the button for
3 sec to start pairing.
C. Pairing may take up
to 2 min.
D. The static icon below
indicates successful pairing.
If pairing fails (E0), make sure the distance between the devices is approximately 3 meters. Pair again by pressing the
button for 3 sec.
2. Pair the Wireless Temp. Sensor
1. Install the Internet Bridge
A. Connect the Internet Bridge to the router.
If no free USB port is available on the router, use the
included 5V power adapter.
B. Press and hold the pairing button until the pairing LED
starts blinking.
2
min
3
sec
Solid on
Blinking
Unfold to check:
Step 4: Wire the Wireless Receiver
Step 5: Pair the Wireless Receiver
Step 6: Configuration
Extra information: Wireless Receiver Symbols
Power supply, testing
mode & configuration
Connection with
other tado˚ devices
Device errors Heat request Hot water request
If there is a wired room thermostat installed in the zone that is intended to be controlled by the Wireless Receiver,
please by bridging the control wires and insulating the other wires with the included 2-terminal decommission it
connector blocks as shown in the images.
Once tado° is installed, the Wireless Receiver will be the only device that controls the heating system.
For Neutral and Earth, Insert only one wire per block, even though the block has more than one opening.
3. Replace the room thermostat
LIVE
(COM) NEUTRAL EARTH
SWITCHED
LIVE (NO)
Caution! Turn OFF the
power before wiring!
Specyfikacje produktu
| Marka: | Tado |
| Kategoria: | termostat |
| Model: | Wireless Temperature Sensor |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Tado Wireless Temperature Sensor, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje termostat Tado
23 Września 2024
4 Września 2024
21 Sierpnia 2024
18 Sierpnia 2024
18 Sierpnia 2024
16 Sierpnia 2024
Instrukcje termostat
- termostat RWE
- termostat Hive
- termostat Carrier
- termostat Ferguson
- termostat Grasslin
- termostat Frico
- termostat Plugwise
- termostat Crestron
- termostat Trotec
- termostat Wachendorff
- termostat Drayton
- termostat Remeha
- termostat Siemens
- termostat Devi
- termostat Boneco
Najnowsze instrukcje dla termostat
9 Kwietnia 2025
9 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
6 Kwietnia 2025
6 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025