Instrukcja obsługi Tandberg Data StorageLibrary T40+
Tandberg Data
Niesklasyfikowane
StorageLibrary T40+
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tandberg Data StorageLibrary T40+ (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 6 użytkowników na średnio 4.7 gwiazdek
Strona 1/4
Quick Installation Steps
For more information and complete step-by-step instructions, please refer to the StorageLibrary T40+ Series
Installation and User Guide available at www.tandbergdata.com .
Warning Although the StorageLibrary T40+ may be lifted by one person when drives, ™
power supply, and magazines are removed, for your protection and safety, we
recommend that two people lift the StorageLibrary™ T40+. All-inclusive library
weight = 38 kg / 84 lbs (2 FH drives). Empty library weight = 23.6 kg / 52 lbs (not
including drives, magazines or power supply).
Caution Please ensure the StorageLibrary T40+ is mounted in the rack before you remove
the transport screws. The transport locking screws must be removed before the
StorageLibrary T40+ can operate normally.
When following the steps below, please refer to the corresponding numbers and letters on the illustrations.
1. Please refer to the StorageLibrary T40+ Series Pass-Thru Installation Manual for instructions of how to
install the unit. To insert the StorageLibrary T40+ onto the rack-rails, please request help of another
person.
2. Before removing the locking screws, power-on the unit. The StorageLibrary T40+ will automatically eject
the magazines if the transport locking screws are mounted. Remove all magazines, remove the four
transport locking screws, and mount the rack mount ears. Re-insert the magazines.
3. Install SCSI, SAS or Fibre Channel cables.
SCSI installation:
Power-off the unit and the host system before plugging in the SCSI cables. When using more than two
SCSI drives, please refer to the StorageLibrary T40+ Series Installation and User Guide for installation
requirements.
a. Connect a SCSI cable from the host to the
1st drive (bottom SCSI connector).
b. Connect a SCSI jumper cable from 1st drive
(top SCSI connector) to the 2nd drive
(bottom SCSI connector). If required repeat
this step for all drive within the tape library.
c. Terminate the last device on the SCSI bus
using the correct SCSI terminator.
NOTE: The maximum SCSI bus length must NOT exceed 9 meters / 30 feet. Please ensure SCSI cables
and teminators are securely fitted using thumbscrews.
SAS installation:
If your library includes tape drives with SAS
interface, connect a SAS cable to each tape
drive separately and connect other end of the
SAS cable to the host.
2
FC installation:
If your library includes tape drives with FC
interface, connect a FC cable to each tape
drive separately and connect other end of the
FC cable to the host, switch or hub.
4. Configuring the library
a. Connect your Ethernet cable to the Ethernet
port at the rear of the library. The library
Ethernet port allows the use of the Web
Client.
b. Connect the two power cords to
the power connectors at the rear of
the library. US and European power cords
are supplied with the library. Two power
cords are required for redundant power supply.
c. Power-on the library (both switches).
d. Power up the host system.
e. Verify that each host can communicate with the library’s tape drives. If you experience problems,
please refer to the troubleshooting guide in the StorageLibrary T40+ Series Installation and User
Guide.
f. Configure your library using the library’s operator panel.
NOTE: The LTO-5 automation tape drives contain an Ethernet port which will enable new features and
functionality at a later time. For more information please refer to www.tandbergdata.com .
Table: Power Requirements
Values
Input Voltage 100 – 240 VAC (1.2 – 0.5 A)
Input Frequency 50 – 60 Hz
Inrush Current (Cold Start) Less than 15 A, 115 VAC
Less than 30 A, 230 VAC
Power Consumption Average 70 W*
Power Consumption Peak* 120 W**
* Value per StorageLibrary T40+ unit with two LTO drives.
** Maximum peak length, less than 10ms.
3
Specyfikacje produktu
| Marka: | Tandberg Data |
| Kategoria: | Niesklasyfikowane |
| Model: | StorageLibrary T40+ |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Tandberg Data StorageLibrary T40+, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Tandberg Data
13 Września 2024
28 Sierpnia 2024
26 Sierpnia 2024
24 Sierpnia 2024
6 Sierpnia 2024
6 Sierpnia 2024
Instrukcje Niesklasyfikowane
- Niesklasyfikowane Rigol
- Niesklasyfikowane Waldbeck
- Niesklasyfikowane Altrad
- Niesklasyfikowane Fisher Price
- Niesklasyfikowane Raspberry Pi
- Niesklasyfikowane Elo
- Niesklasyfikowane Fagor
- Niesklasyfikowane A3
- Niesklasyfikowane Capital Sports
- Niesklasyfikowane JL Cooper
- Niesklasyfikowane Evooch
- Niesklasyfikowane Carrier
- Niesklasyfikowane Aluratek
- Niesklasyfikowane ChamSys
- Niesklasyfikowane Alpine
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025