Instrukcja obsługi Tripp Lite 4POSTRAILKITHD
Tripp Lite
Niesklasyfikowane
4POSTRAILKITHD
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite 4POSTRAILKITHD (4 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 23 osób i została oceniona przez 12 użytkowników na średnio 5.0 gwiazdek
Strona 1/4
B
A
A
A
A
B
1
2
2
B
B
C
C
C
C
2U
3U AND ABOVE
1
Owner's Manual
4POSTRAILKITHD
Heavy-Duty Adjustable Rackmount Shelf Kit
Important Safety Instructions
Español / Français : 3
Installation
SAVE THESE INSTRUCTIONS
This manual contains instructions and warnings that must be followed during the installation and operation of the product described in this manual.
Failure to comply may invalidate the warranty and cause property damage or personal injury.
• Use the included shelves and mounting hardware to mount your rackmount equipment in a 4-post rack or rack enclosure. If you need to install your
equipment in a 2-post rack, order Tripp Lite’s 2-Post Rackmount Kit (model: 2POSTRMKITWM).
• The instructions in this manual are for common rack and rack enclosure types and may not be appropriate for all mounting applications. You must
determine the fitness of hardware and procedures before mounting. If hardware or procedures are not suitable for your application, contact the
manufacturer of your rack or rack enclosure for a solution.
• Rackmount equipment may be extremely heavy—be careful when moving or lifting equipment. Use one or more assistants if necessary.
Square-Hole Rack Installation
1 The included plastic pegs A will temporarily support the empty
rackmount shelves B while you install the permanent mounting
hardware. Insert a peg near the center of the front and rear bracket of
each shelf as shown. (Each front bracket has 6 holes and each rear
bracket has 3 holes.) The pegs will snap into place.
After installing the pegs, expand each shelf to match the depth of your
rack rails. The pegs will fit through the square holes in the rack rails to
support the shelves. Refer to the rack unit labels to confirm that the
shelves are level in all directions. Note: The support ledge of each
shelf must face inward.
2 Secure the shelves B to the mounting rails permanently using the
included screws and cup washers C as shown.
• For 2U equipment mounting, place 4 screws total at the front and
4 screws total at the back.
• For 3U and above equipment mounting, place 6 screws total at the
front and 4 screws total at the back.
Tighten all screws before proceeding.
Warning: Do not attempt to install your equipment until you
have inserted and tightened the required screws. The plastic
pegs will not support the weight of your equipment.
1111 W. 35th St., Chicago, IL 60609 USA • www.tripplite.com/support
Specyfikacje produktu
| Marka: | Tripp Lite |
| Kategoria: | Niesklasyfikowane |
| Model: | 4POSTRAILKITHD |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Tripp Lite 4POSTRAILKITHD, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Tripp Lite
15 Stycznia 2025
15 Stycznia 2025
15 Stycznia 2025
15 Stycznia 2025
15 Stycznia 2025
15 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
9 Stycznia 2025
Instrukcje Niesklasyfikowane
- Gembird
- Elba
- Leaptel
- Barkan
- Deaf Bonce
- MSI
- Twinkly
- Trio Lighting
- Vortex
- Homedics
- TrueLife
- EasyMaxx
- Gerni
- AVer
- Bearware
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025