Instrukcja obsługi Tripp Lite PS3612RA

Tripp Lite nieskategoryzowany PS3612RA

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite PS3612RA (12 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 48 osób i została oceniona przez 24.5 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/12

Power Strips

Models: PS120406, PS120420, PS240406, PS2408RA,

PS240810, PS3612RA, PS361206, PS361220 and

PS480806

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Owner’s Manual

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $50 value!

www.tripplite.com/warranty

PS-Series Power Strips are designed to provide convenient access to multiple AC outlets.

Note: The Power Strip models listed above DO NOT provide your connected equipment with surge or line-noise

protection.

Important Safety Instructions 2

Equipment Connection 2

Wall Mounting 2

Speciﬁcations 3

Warranty and 4

Product Registration

Español 5

Français 9

15-02-180-933408.indb 1 2/18/2015 10:41:57 AM

Equipment Connection

Plug your equipment into the Power Strip’s AC receptacles. DO NOT plug in equipment that draws

more total amps than your Power Strip’s amperage rating (see label on Power Strip for amperage

rating), or you will trip the circuit breaker. If the circuit breaker trips, remove overload and depress

breaker to reset. Leave enough clearance at the end of the Power Strip to allow the circuit

breaker to operate normally.

Note: Select models with a power switch feature a protective switch cover. To access the switch, ﬂip open the

attached cover.

Wall Mounting

All Power Strip models feature clips for horizontal or vertical mounting on a variety of surfaces.

The user must supply other mounting hardware (screws, etc.) and determine its suitability for use

with the chosen mounting surface.

1 Mark a straight horizontal or vertical line where

you want to mount the Power Strip. At each end

of the line, mark where the edges of the Power

Strip will be located. Place a mounting clip on

the mounting surface 1” (2.54 cm) in from

these edges and mark where the screws must

be driven into the wall. For strips longer than

48” (120 cm), also mark a screw hole for a third

mounting clip midway between the other two.

2 Keyhole Mounting: Drive #8 screws directly

into the mounting surface. Snap the mounting

clips onto the Power Strip 2a , then hang the

Power Strip on the screws by the keyhole slots

on its mounting clips 2b.

Important Safety Instructions

SAVE THESE INSTRUCTIONS

• DO NOT connect the power strip to an ungrounded outlet.

• DO NOT use the power strip with 2-wire extension cords or adapters.

• This power strip is designed for indoor use only. Install the power strip away from heat-emitting

appliances such as radiators or heat registers.

• Do not install where excessive moisture is present.

• Do not plug extension cords into the power strip.

• Never install electrical, telephone, network or coaxial wiring during a lightning storm.

• Do not drill into any part of the housing or open the housing for any reason. There are no

user-serviceable parts inside.

15-02-180-933408.indb 2 2/18/2015 10:41:58 AM

Speciﬁcations

Model

Amperage

Rating

Outlet

Qty. x Type

Input

Plug

Cord

Length

Overall

Length Breaker

PS120406 15A 4 x 5-15R 5-15P 6 ft. 12 in. 15A

PS120420 20A 2 x 5-20R, 2 x 5-15R 5-20P 15 ft. 12 in. 20A

PS240406 15A 4 x 5-15R 5-15P 6 ft. 24 in. 15A

PS2408RA 15A 8 x 5-15R* 5-15P* 15 ft. 24 in. 15A

PS240810 15A 8 x 5-15R 5-15P 10 ft. 24 in. 15A

PS3612RA 15A 12 x 5-15R* 5-15P* 15 ft. 36 in. 15A

PS361206 15A 12 x 5-15R 5-15P 6 ft. 36 in. 15A

PS361220 20A 2 x 5-20R, 10 x 5-15R 5-20P 15 ft. 36 in. 20A

PS480806 15A 8 x 5-15R 5-15P 6 ft. 48 in. 15A

*Right-angle

Wall Mounting (Continued)

3a 3b

3 Clip Mounting: Drive #10 screws through

washers, through the centers of the mounting

clips and into the mounting surface

3a. Place

the Power Strip inside one edge of the mounting

clips, then snap the Power Strip into place

3b.

15-02-180-933408.indb 3 2/18/2015 10:41:58 AM

Specyfikacje produktu

Marka:	Tripp Lite
Kategoria:	nieskategoryzowany
Model:	PS3612RA
Kolor produktu:	Black, Metallic
Materiał obudowy:	Aluminium
Wbudowany wyłącznik:	Tak
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	120 V
Wysokość produktu:	31.8 mm
Szerokość produktu:	38.1 mm
Głębokość produktu:	914.4 mm
Waga produktu:	1470 g
Długość kabla:	4.5 m
Szerokość opakowania:	116.8 mm
Wysokość opakowania:	61 mm
Głębokość opakowania:	1016 mm
Certyfikaty:	cUL, UL1363
Kraj pochodzenia:	Chiny
Przeznaczenie:	Wewnętrzna
Waga wraz z opakowaniem:	1810 g
Wysokość skrzyni wzorcowej (zewnętrznej):	360.7 mm
Długość skrzyni głównej (zewnętrznej):	1031.2 mm
Waga brutto obudowy głównej (zewnętrznej):	22140 g
Szerokość skrzyni zbiorczej (zewnętrznej):	266.7 mm
W opakowaniu zbiorczym GTIN (EAN / UPC):	10037332187465
Maksymalne natężenie prądu:	15 A
Liczba dołączonych produktów:	1 szt.
Maksymalna moc wejściowa:	1800 W
Kolor kabla:	Czarny
Produkty w skrzyni głównej (zewnętrznej):	12 szt.
Ilość gniazd sieciowych:	12 x gniazdo sieciowe
Typy wyjść AC:	NEMA 5–15R