Instrukcja obsługi Tripp Lite PSC360610USBB

Tripp Lite nieskategoryzowany PSC360610USBB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tripp Lite PSC360610USBB (12 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 3 użytkowników na średnio 4.2 gwiazdek

Pobierz PDF

Strona 1/12

Power Strips

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Owner’s Manual

Note: Power Strip models DO NOT provide your connected equipment

with surge or line-noise protection.

Important Safety Instructions 2

Clamp Mounting 2

Wall Mounting 3

Equipment Connection 3

Warranty and Product Registration 4

Español 5

Français 9

WARRANTY REGISTRATION

automatically entered to win an ISOBAR

surge protector in our monthly drawing!

www.tripplite.com/warranty

19-03-135-933971.indb 1 4/4/2019 11:02:35 AM

Important Safety Instructions

Clamp Mounting (Included with Select Models)

SAVE THESE INSTRUCTIONS

• DO NOT connect the power strip to an ungrounded outlet.

• DO NOT use the power strip with 2-wire extension cords or adapters.

• This power strip is designed for indoor use only. Install the power strip away from heat-emitting

appliances such as radiators or heat registers.

• Do not install where excessive moisture is present.

• Do not plug extension cords into the power strip.

• Never install electrical, telephone, network or coaxial wiring during a lightning storm.

• Do not drill into any part of the housing or open the housing for any reason. There are no

user-serviceable parts inside.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to signiﬁcantly

affect its safety or effectiveness is not recommended.

Clamp mounts attach to a desk, tabletop, workbench or other solid, ﬂat surface. Your Tripp Lite

Power Strip is compatible with the clamp mounts. For power strip models that do not include

clamp mounts, clamps can be purchased at www.tripplite.com.

1 To install the clamp, loosen the knob, then slide

the clamp ﬁrmly onto the edge of an appropriate

surface. Turn the knob to tighten and secure the

clamp to the surface. Repeat for any additional

clamps.

Note: If the mounting clip is loose, use a screwdriver to

tighten the screw.

2 Push the Power Strip into the clamp mount

clip(s) until it securely snaps into place.

19-03-135-933971.indb 2 4/4/2019 11:02:35 AM

Equipment Connection

Plug your equipment into the Power Strip’s AC receptacles. DO NOT plug in equipment that draws

more total amps than your Power Strip’s amperage rating (see label on Power Strip for amperage

rating), or you will trip the circuit breaker. If the circuit breaker trips, remove overload and depress

breaker to reset. Leave enough clearance at the end of the Power Strip to allow the circuit

breaker to operate normally.

Note: Select models with a power switch feature a protective switch cover. To access the switch, ﬂip open the

attached cover.

Wall Mounting

All Power Strip models feature clips for horizontal or vertical mounting on a variety of surfaces.

1 Check Clip Type: Your Power Strip will contain

one of two types of mounting clips, depending

on the model.

2 Mark a straight horizontal or vertical line where

you want to mount the Power Strip. At each end

of the line, mark where the edges of the Power

Strip will be located. Place a mounting clip on

the mounting surface 1” in from these edges

and mark where the screws must be driven into

the wall. For strips longer than 48” (120 cm),

also mark a screw hole for a third mounting clip

midway between the other two.

3a Clip-A Mounting: Drive #8 screws directly into

the mounting surface, leaving approximately

3 mm of space between the screw head and

the surface. Snap the mounting clips onto the

Power Strip 3a1 , then hang the Power Strip

on the screws by the keyhole slots on its

mounting clips 3a2.

3b Clip-B Mounting: Pre-drill holes in the mounting

surface, if necessary. Drive screws through

the centers of the mounting clips and into the

mounting surface 3b1. Place the Power Strip

inside one edge of the mounting clips,

then snap the Power Strip into place

3b2 .

3b1 3b23b2

3a1

3a2

Clip-A Clip-B

19-03-135-933971.indb 3 4/4/2019 11:02:36 AM

Specyfikacje produktu

Marka:	Tripp Lite
Kategoria:	nieskategoryzowany
Model:	PSC360610USBB
Kolor produktu:	Czarny
Wbudowany wyłącznik:	Tak
Częstotliwość wejściowa AC:	50 - 60 Hz
Wysokość produktu:	914.4 mm
Szerokość produktu:	38.1 mm
Głębokość produktu:	41.7 mm
Waga produktu:	1360 g
Długość kabla:	3.05 m
Szerokość opakowania:	104.1 mm
Wysokość opakowania:	55.9 mm
Głębokość opakowania:	1016 mm
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Certyfikaty:	UL1363, cUL
Kraj pochodzenia:	Chiny
Waga wraz z opakowaniem:	1860 g
Wysokość skrzyni wzorcowej (zewnętrznej):	315 mm
Długość skrzyni głównej (zewnętrznej):	1033.8 mm
Waga brutto obudowy głównej (zewnętrznej):	19320 g
Szerokość skrzyni zbiorczej (zewnętrznej):	241.3 mm
Diody LED:	Tak
W opakowaniu zbiorczym GTIN (EAN / UPC):	10037332238815
Liczba dołączonych produktów:	1 szt.
Materiały:	Aluminium
Produkty w skrzyni głównej (zewnętrznej):	10 szt.
Wartość znamionowa udaru energii:	- J
Ilość gniazd sieciowych:	15 x gniazdo sieciowe
Typy wyjść AC:	NEMA 5–15R
Wartość nominalna napięcia wejściowego:	120 V
Moc szczytowa:	1800 W
Wtyczka:	NEMA 1–15P
Nominalne natężenie prądu na wyjściu:	9.3 A