Instrukcja obsługi Waterco Electroheat MKV
Waterco
pompa ciepła
Electroheat MKV
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Waterco Electroheat MKV (36 stron) w kategorii pompa ciepła. Ta instrukcja była pomocna dla 32 osób i została oceniona przez 16.5 użytkowników na średnio 4.9 gwiazdek
Strona 1/36
www.waterco.com
Installation and
Operation Manual
This equipment must be installed and serviced by a qualified technician.
Improper installation can create electrical hazards which could result in property
damage, serious injury or death. Improper installation will void the warranty.
Notice to Installer
This manual contains important information about the installation, operation and
safe use of this product. Once the product has been installed this manual must
be given to the owner/operator of this equipment.
WARNING
!
WATERCO POOL HEAT PUMP
FLOW
Contents
Table of
IMPORTANT SAFETY INSTRUCTIONS
------------
02
A NOTE TO YOU
--------------------------------------
03
INSTALLATION INSTRUCTIONS
--------------------
05
Location
------------------------------------------
05
Installation Clearances
--------------------------
06
Water Piping
-------------------------------------
07
Water Flow Rate
---------------------------------
07
Water By-pass Kit
-------------------------------
07
Plumbing Diagram
------------------------------
08
Electrical
------------------------------------------
09
Electrical Connection
---------------------------
09
Breaker Size -------------------------------------- 09
Electrical Wire Size
------------------------------
09
Bonding
-------------------------------------------
10
Bonding Diagram
--------------------------------
10
Quick Connector --------------
------------------
11
Connection Overview ---------
------------------
11
Wiring Diagram ---------
-------------------------
12
Setting Up Quick Connector For Heat Pump -- 12
(9kW ~15kW)
Quick Connector For Heat Pump ------------- 13 & 15
(25kW ~44kW)
Water Pump Control (First time set-up)
-----
13
Pump Control Sequence
------------------------
14
Usage Of Chemical Products ------------------ 15
Performance Specications -------------------- 16
WIFI SET UP INSTRUCTIONS
-----------------
17
Install the Waterco Connect app
--------------
17
Pair your Electroheat to your app
-------------
18
Troubleshooting ---------------------
------------
20
OPERATION OF YOUR POOL HEAT PUMP
--------
21
CONTROLLER TYPES
Initial Heating
------------------------------------
21
Adjustment Of The Bypass Valves
------------
21
Pool Heat Pump Running Time
----------------
22
Pool Solar Blanket
-------------------------------
22
Defrost Cycle
-------------------------------------
22
To Start The Pool Heat Pump ------------------ 23
To Stop The Pool Heat Pump ------------------ 23
To Check and Adjust Temperature
Settings ------------------------------------------- 24
Temperature Calibration
------------------------
25
To Change Display From Farenheit To
Celcius
--------------------------------------------
26
Defrost for Electroheat Ultra
-------------------
26
Protection Devices
------------------------------
26
Codes
---------------------------------------------
26
INVERTER POOL HEAT PUMP CONTROLLER
----
27
Inverter Controller Operation
------------------------
28
Timer Function
-----------------------------------
28
Function Descriptions
--------------------------
29
Buzzer --------------------------------------------- 29
Memory Function
--------------------------------
29
MAINTENANCE OF YOUR POOL HEAT PUMP
----
30
Cabinet Cleaning
--------------------------------------
30
Cleaning Evaporator
----------------------------------
30
Cleaning drainage holes
------------------------------
30
Units Located In Coastal Locations
-----------------
30
Winterising Procedure
--------------------------------
31
GENERAL SAFETY INSTRUCTIONS
----------------
32
TROUBLESHOOTING
---------------------------------
33
Nothing Is Working and The
Electronic Control Does Not Operate
--------
33
Nothing Is Working But The Electronic
-------
33
Control Temperature Displays Digits
----------
33
or a Code
Fan Doesn’t Work (The Fan Blades
-----------
33
Are Not Moving)
Fan Blades Turn, But Compressor Is Not
-----
34
Functioning
Compressor Starts and Stops
-----------------
34
There Is Water Around The Pool Heat
---------
34
Pump
Pool Heat Pump Has Ice Formed On The
----
35
Evaporator Coil
Pool Heat Pump Is Functioning, But Does
---
35
Not Reach The Desired Temperature
Setting
Analysis Chart
------------------------------------
36
Circuit Breaker Trips
-----------------------------
36
The Pool Heat Pump Is Noisy
------------------
37
The Temperature Shown On Pool Heat
-------
37
Pump Is Not The Same That Is
Shown By The Pool Thermometer
Service Analyser Codes
-------------------------
38
WARRANTY -------------------------------------------- 42
I pg 02
Pool Heat Pump
IMPORTANT SAFETY INSTRUCTIONS
When using this electrical equipment, basic safety precautions should always be
followed, including the following:
READ AND FOLLOW ALL INSTRUCTIONS
! WARNING: Disconnect all AC power during installation and servicing.
! WARNING: In order to avoid the possibility of hyperthermia (heat stress) occurring
it is recommended the average temperature of the spa - pool water does not exceed
40˚C.
! WARNING: The pool heat pump is not intended for use by persons (including
children) with reduced physical sensory or mental capabilities, or lack of experience
and knowledge, unless they have been provided supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be
supervised to ensure they do not play with the appliance.
• In certain situations unexpected start up may occur when the appliance is in
automatic mode.
• The installer should assess the risk associated with unexpected start-up of this
device which, in any circumstance should have no hazardous effect.
• The pool heat pump is not meant to provide safety protection for other devices.
• The pool heat pump should be deactivated if the pool or spa has been drained.
• Waterco pool heat pumps must be installed by a suitably qualied person in
accordance with current Regulatory Standards, the applicable Wiring Rules
(AS3000) and local statutory authority regulations.
• Parts containing live parts, except parts supplied with safety extra-low voltage
not exceeding 12V, must be inaccessible to a person in the spa – pool.
• Parts incorporating electrical components, except remote control devices, must
be located or xed so that they cannot fall into the spa – pool.
• The appliance should be supplied through a residual current device (RCD) having
a rated residual operating current not exceeding 30mA.
• An Earth terminal is located inside the wiring enclosure. To reduce the risk of
electric shock, this terminal must be connected to the grounding means provided
in the electric supply service panel with a continuous copper wire as sized to
comply with current Standards and local statutory authorities in relation to the
circuit conductors supplying the equipment.
• A cable connector is provided on this unit to connect a suitably sized copper
conductor between this unit and any metal equipment, metal enclosures of
electrical equipment, metal water pipe, or conduit within 1.5m of the unit via
equipotential bonding.
SAVE THESE INSTRUCTIONS.
Specyfikacje produktu
| Marka: | Waterco |
| Kategoria: | pompa ciepła |
| Model: | Electroheat MKV |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Waterco Electroheat MKV, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje pompa ciepła Waterco
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
3 Października 2024
24 Maja 2024
Instrukcje pompa ciepła
- Wilo
- Nefit
- Wita
- Fisher & Paykel
- Hotpoint
- Olimpia Splendid
- Remko
- Vivax
- Zodiac
- Elco
- Grundfos
- Itho-Daalderop
- Artel
- Azuro
- Blaupunkt
Najnowsze instrukcje dla pompa ciepła
6 Kwietnia 2025
6 Kwietnia 2025
6 Kwietnia 2025
6 Kwietnia 2025
4 Kwietnia 2025
4 Kwietnia 2025
3 Kwietnia 2025
2 Kwietnia 2025
2 Kwietnia 2025
31 Marca 2025