Instrukcja obsługi Weller WPA2N
Weller
maszyna do lutowania
WPA2N
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Weller WPA2N (4 stron) w kategorii maszyna do lutowania. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 9 użytkowników na średnio 4.3 gwiazdek
Strona 1/4
IMPORTANT
For best performance and your safety, please read and familiarize yourself
with these instruction before using the tool.
1. Avoid dropping the tool or causing hard shocks as the ceramic burner or
fuel view window could be damaged.
2. Use an exhaust fan when using tool in an enclosed space.
3. Do not fill tool with gas or store near open flame, heater, furnace or
combustible materials.
4. Do not store in direct sunlight or anywhere that will exceed 40°C or 104°F.
5. Keep out of reach of children.
6. When not in use ensure the gas ON/OFF lever is in the OFF position.
7. Do not attempt to change soldering or hotblow tips or perform any kind of
maintenance while tool is still hot.
8. Do not misuse, abuse, alter or tamper with the tool in any way.
Only authorized people should carry out repairs.
9. Do not speed cool hot parts in water. Allow to cool naturally.
10. When operating at low temperatures, around 0°C or 32°F or lower, ignition
may be difficult. Hold handle in warm hands for a few minutes until liquid
fuel gasses. Never use an open flame or hot water to warm fuel.
11. Do not use alcohol or alcohol based cleaner on fuel window.
OPERATING PROCEDURE
1. It is most important to ensure that the exhaust opening in the tip is pointed
upwards, as above, when fitting the tip. At all times ensure the opening is
facing away from hands and combustible materials when the tool is ignited
as the exhaust temperature is very high. The tip housing can aslo reach high
temperatures. Ignition problems will result if ignition is attempted with tip
or tip housing removed.
2. Set gas control lever to 3, set gas ON/OFF
lever to ON. In cold temperature or immediately
after filling gas, it may be necessary
to use a higher setting than 3.
3. Push the ignition button slowly to ignite the tool.
4. Wait until the window at the base of the tip goes
red. If the tool fails to ignite repeat step 3.
5. Adjust tip temperature with gas control lever.
6. To turn off slide the gas ON/OFF lever to the left
until it clicks OFF.
Note, the gas control lever will turn the toolnot
off.
It is recommended to leave the gas control set at
5 if the tool is not going to be used for long
periods. This will keep the fuel wick in good full
flow condition.
SELF-IGNITING
CORDLESS PYROPEN
®
WPA2N / WSTA4
GAS-FILLING
Use Weller gas refill part no T0051616099 only.
1. Check gas level through window in handle.
2. Be sure the gas ON/OFF lever is at "OFF" position.
3. Hold the Pyropen
®
handle with tip pointing downward and,
refill nozzle in upright position. Insert nozzle of gas container
and press down.
4. As soon as the Pyropen
®
is filled, gas will overflow.
5. Confirm the gas reservoir is full by checking gas level in
the sight glass.
TIP CHANGING PROCEDURE
1. Unscrew knurled tip housing nut clock-wise and remove
housing.
2. Remove old tip and postion new tip.
3. Slide housing in place and tighten housing nut.
Back off one turn then turn housing until igniter pin clicks
into slot in housing lip.
4. Position tip so that exhaust opening is facing up.
5. Tighten knurled housing nut.
G Tip
Exhaust opening
F Tip housing
C Window
E Kurled nut
B Ignition button
D ON/OFF Lever
A Control Lever
1-5
Gas Lever window
Handle containing butane gas
Gas refill nozzle
Specyfikacje produktu
| Marka: | Weller |
| Kategoria: | maszyna do lutowania |
| Model: | WPA2N |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Weller WPA2N, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje maszyna do lutowania Weller
3 Stycznia 2025
3 Stycznia 2025
31 Grudnia 2025
12 Października 2024
30 Września 2024
30 Września 2024
29 Września 2024
25 Września 2024
22 Września 2024
20 Września 2024
Instrukcje maszyna do lutowania
- GYS
- Hakko
- Awelco
- Trotec
- Craftsman
- BaseTech
- DEDRA
- Uten
- Westfalia
- Fixpoint
- Telwin
- Parkside
- Monacor
- UNIMIG
- Powerfix
Najnowsze instrukcje dla maszyna do lutowania
11 Stycznia 2025
5 Stycznia 2025
4 Stycznia 2025
4 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
1 Stycznia 2025
29 Grudnia 2024
26 Grudnia 2024