Instrukcja obsługi ACP ACE14
ACP
Magnetostrykcja
ACE14
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla ACP ACE14 (15 stron) w kategorii Magnetostrykcja. Ta instrukcja była pomocna dla 23 osób i została oceniona przez 12 użytkowników na średnio 4.8 gwiazdek
Strona 1/15
Commercial Combination Oven
(Microwave and Convection)
Keep these instructions for future
reference. If the equipment changes
ownership, be sure this manual
accompanies equipment.
Owner’s Manual
Contents
Model Identication ................................... 2
Grounding Instructions .............................. 3
Installation ................................................. 3
Display and Features ................................ 4
Programming ............................................. 7
Convection Cooking .................................. 8
Combination Cooking
(microwave and convection) .................. 9
Microwave Cooking (microwave only).....10
User Options ............................................11
USB Flash Drive Operating Instructions . 12
User Maintenance ................................... 13
Service Codes ......................................... 13
Care and Cleaning .................................. 14
Before Calling Service ............................. 15
FOR COMMERCIAL USE ONLY
This manual covers model: ACE*
Original Instruction
2
– Inside the U.S.A. or Canada, call toll-free at
866-426-2621.
– Outside the U.S.A. and Canada, call 319-368-8120.
– Email: Commercialservice@acpsolutions.com.
Warranty service must be performed by an authorized
ACP servicer. ACP also recommends contacting an
authorized ACP servicer, or ACP ComServ Service
Support if service is required after warranty expires.
Model Identication
When contacting ACP, provide product information. Product information is located on oven serial plate.
Record the following information:
Model Number: _____________________________
Serial or S/N Number: ________________________
Date of installation: __________________________
Dealer’s name and address: ___________________
__________________________________________
__________________________________________
Any questions or to locate an authorized ACP servicer,
call ACP ComServ Service Support.
3
Installation
Unpacking Oven
• Inspect oven for damage such as dents in door or inside oven cavity.
• Report any dents or breakage to source of purchase immediately.
Do not attempt to use oven if damaged.
• Remove all materials from oven interior.
• If oven has been stored in extremely cold area, wait a few hours before
connecting power.
Radio Interference
Microwave operation may cause interference to radio, television, or a similar
oven. Reduce or eliminate interference by doing the following:
• Clean door and sealing surfaces of oven according to instructions in
Care and Cleaning section.
• Place radio, television, etc. as far as possible from oven.
• Use a properly installed antenna on radio, television, etc. to obtain
stronger signal reception.
Oven Placement
• Do not install oven next to or above source of heat, such as pizza oven
or deep fat fryer. This could cause microwave oven to operate
improperly and could shorten life of electrical parts.
• Do not block or obstruct oven lter. Allow access for cleaning.
• Install oven on level countertop surface.
• If provided, place warning label in a conspicuous place close to
microwave oven.
• Outlet should be located so that plug is accessible when oven is in place.
Oven Clearances
A—Allow at least 4” (10 cm) of clearance around top of oven. Proper
air ow around oven cools electrical components. With restricted
air ow, oven may not operate properly and life of electrical parts is
reduced.
B—There is not an installation clearance requirement for the back of the
oven.
C—Allow at least 1” (2.54 cm) of clearance around sides of oven.
D—Install combination oven so oven bottom is at least 3 feet (91.5 cm)
above oor.
To avoid risk of electrical shock
or death, this oven must be
grounded and plug must not be
altered.
Earthing
Instructions
Oven MUST
be grounded.
Grounding reduces
risk of electric shock by providing an
escape wire for the electric current
if an electrical short occurs. This
oven is equipped with a cord having
a grounding wire with a grounding
plug. The plug must be plugged into
an outlet that is properly installed
and grounded.
Consult a qualied electrician or
servicer if grounding instructions
are not completely understood, or if
doubt exists as to whether the oven
is properly grounded.
Do not use an extension cord.
If the product power cord is too
short, have a qualied electrician
install a three-slot receptacle.
This oven should be plugged
into a separate circuit with the
electrical rating as provided in
product specications. When the
combination oven is on a circuit with
other equipment, an increase in
cooking times may be required and
fuses can be blown.
External Equipotential
Earthing Terminal (export only)
Equipment has secondary earthing
terminal. Terminal provides external
earthing connection used in addition
to earthing prong on plug. Located
on outside of oven back, terminal is
marked with symbol shown below.
A
B
C
Specyfikacje produktu
| Marka: | ACP |
| Kategoria: | Magnetostrykcja |
| Model: | ACE14 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z ACP ACE14, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Magnetostrykcja ACP
30 Stycznia 2025
28 Stycznia 2025
27 Stycznia 2025
19 Stycznia 2025
19 Stycznia 2025
18 Stycznia 2025
18 Stycznia 2025
18 Stycznia 2025
18 Stycznia 2025
18 Stycznia 2025
Instrukcje Magnetostrykcja
- Atag
- AKAI
- Küppersbusch
- Universal Blue
- Inventum
- H.Koenig
- Gaggenau
- Rinnai
- Airlux
- Insignia
- Fagor
- Ursus Trotter
- Hanseatic
- Furrion
- Electrolux-Rex
Najnowsze instrukcje dla Magnetostrykcja
9 Kwietnia 2025
9 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025
7 Kwietnia 2025