Instrukcja obsługi AFX Chappelle 126509
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AFX Chappelle 126509 (2 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/2
LED Indoor Fixed Rail Luminaires
Surface Mount
120VAC / 60Hz
Exclusively Distributed B To Reorder: y:
HD Supply Facilities Maintenance, Ltd.
Atlanta, GA 30339 1- -431-3000 800
© 2019 hdsupplysolutions.com
Made in China
Part #: 126509
Safety Precautions
Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially
fatal electric shock and/or property damage.
It is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes.
Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.
This xture is designed for use in a 110-120VAC, 60Hz fused circuit and can be used in conjunction with 2-wire, triac dimmers. most
To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate
ground wire (green) contact between this xture and the ground connection of your main power supply panel.
This xture is intended to be used for general indoor lighting in dry or damp locations only.
Disclaimer
Changes or modications not expressly approved by the party responsible for compliance could void NOTE: This equipment the user’s authority to operate the equipment.
has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005 (B). These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult with the dealer or an experienced radio/TV technician for help.
Any modications to this xture may void the warranty and interfere with the safe operation of the luminaire.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
ASSEMBLY INSTRUCTIONS
Step 1 Preparing for installation–
A. at fuse or circuit breaker box before installing or Disconnect electrical power
servicing any part of this xture.
B. Carefully remove the xture from the carton.
C. Remove gem bar (2) from the xture base by removing two screws (3).
D. Install gem bar (2) on the junction box (not included) by securing it with two screws
(4).
Wiring All wiring must take place inside junction box (not included). –
Caution: Make sure power is off at fuse or circuit breaker box. Check power wires for
damage or scrapes. If power supply wires are within three inches of the LED driver, use
wire suitable for at least °C (194°F). 90
Note: Most dwellings built before 1985 have supply wire rated to °C. Consult a qualied 60
electrician before installing.
Step 2 Wiring xture –
A. Make all wire connections to appropriate wire. Secure with wire nuts ( - provided) 5 .
B. Connect the green wire from the xture to the supply power source ground wire.
C. Connect the black wire from the xture to the black ) wire from supply power (L
source.
D. Connect the white wire from the xture to the white (N) wire from supply power
source.
E. Pull on each wire lead to make sure connections are secure. Make certain no bare
wires are exposed outside of wire connectors. Tuck all connections neatly into the
junction box.
Step 3 Mounting –
A. Install xture (1) over the gem bar (2) by aligning two holes on the side and secure with two
screws (3).
B. Mark exact location for the rail supports on each side of the arm. Unscrew mounting coupler
(7) (8) from rail supports. Secure coupler with wood screw if use on wood and or with plastic
anchor use drywall application. Secure both rail supports onto the mounting (6) if on
couplers ) by tightening the cup (7 .
Step 4 Restore power at fuse or circuit breaker box–
8060798 R1
For reference only.
Individual models
may vary.
Luminous Intensity Distribution
Specyfikacje produktu
| Marka: | AFX |
| Kategoria: | Ulga |
| Model: | Chappelle 126509 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z AFX Chappelle 126509, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ulga AFX
2 Kwietnia 2025
12 Października 2024
12 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
Instrukcje Ulga
- Stairville
- IFM
- Miomare
- Vimar
- EnGenius
- DMT
- Wachsmuth - Krogmann
- Swisson
- Theben
- Hama
- 9.solutions
- Wetelux
- QTX
- Nedis
- Hudson Valley
Najnowsze instrukcje dla Ulga
9 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
7 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025