Instrukcja obsługi AFX Satellite STLF4450L30SN
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AFX Satellite STLF4450L30SN (2 stron) w kategorii Ulga. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 9 użytkowników na średnio 4.7 gwiazdek
Strona 1/2
LED Indoor Luminaires Model # STLF4450L30SN
Fixed Rail Ceiling Mount
120VAC / 60Hz
Page 1 of 2 8061273 R0
Luminous Intensity Distribution
Safety Precautions
Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in potentially fatal
electric shock and/or property damage.
It is recommended that a qualied electrician perform all wiring. This xture must be wired in accordance with all national and local electrical codes.
Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.
This xture is designed for use in a 120VAC, 60Hz fused circuit. This xture is compatible with 2-wire Triac dimmers. / ELV
Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).
To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a separate ground
wire (green) contact between this xture and the ground connection of your main power supply panel.
This xture is intended to be used for general indoor lighting in dry or damp locations.
Disclaimer
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been
tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES- -005 (B). These limits are designed to 005 (B) / NMB
provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult with the dealer or an experienced radio/TV technician for help.
Any modications to this xture may void the warranty and interfere with the safe operation of the luminai re.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Assembly Instructions
1. Preparing for installation.
A. Disconnect electrical power before installing or servicing
any part of this xture.
B. Remove xture from carton; remove components from
hardware kit.
C. Remove round gem bar (2 from the xture by removing two )
screws (3).
D. Install round gem bar (2) to junction box (not provided) by
securing it with two #8- screws (4). 32
2. Wiring.
All wiring must take place inside junction box (not included).
Caution: Make sure power is o at fuse or circuit breaker box.
Check power wires for damage or scrapes. If the power supply
wires are within three inches of the driver, use a wire suitable for at least 90C (194F).
Note: Most dwellings built before 1985 have supply wire rated to 60C. Consult a
qualied electrician before installing.
A. This unit will not operate properly unless connected to a “grounded” electrical
circuit. Electrical shock, overheating, low or no light output, and shortened
LED life can result if proper grounding is not done. Securely attach power
source ground wire and xture ground wire to green ground screw on
rectangular mounting bracket.
B. Make all wire connections to appropriate wire. Secure with wire nuts
(provided).
C. For none-dimming xture. Fixture will operate normally w/o connection to
any dimmers. Connect white xture lead to white (N) wire from supply power
source. Connect black xture lead to black (L) wire from supply power source.
D. For TRIAC dimming. Connect white xture lead to white (N) wire from
dimming source dimmer wiring instructions. Connect black xture lead to per
black (L) wire from dimming source per dimmer wiring instructions.
E. Do not mix wires. Pull on each wire lead to make sure connections are
secure. Make certain no bare wires are exposed outside of wire connectors.
Tuck all connections neatly into junction box.
3. Mounting.
A. Install xture (1) to round gem bar (2) with two screws (3).
4. Power to the xture can now be restored.
Specyfikacje produktu
| Marka: | AFX |
| Kategoria: | Ulga |
| Model: | Satellite STLF4450L30SN |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z AFX Satellite STLF4450L30SN, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Ulga AFX
2 Kwietnia 2025
12 Października 2024
12 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
Instrukcje Ulga
- Maxxworld
- Dainolite
- Maginon
- Altman
- Adviti
- Beghelli
- HiKOKI
- Chamberlain
- NZXT
- Luxli
- Peerless-AV
- Melinera
- Kogan
- Litegear
- 9.solutions
Najnowsze instrukcje dla Ulga
9 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
8 Kwietnia 2025
7 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025
5 Kwietnia 2025