Instrukcja obsługi BlendMount BCB-2025
BlendMount
Niesklasyfikowane
BCB-2025
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BlendMount BCB-2025 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 7 użytkowników na średnio 4.6 gwiazdek
Strona 1/2
PART# BCB-2025
Hien
oun-t®
1
HI~~
~~IJ
I
II
J
IJl
j
lj
ljl
l~
5
Innovat
i
ve
Mount
i
ng
Solut
ions
&cobra
·
LEFT HAND DRIVE VEHICLE
INSTALLATION INSTRUCTIONS FOR THE
COBRA
DSP-9200BT, SPX-7800BTl7700, SPX-6700,
AND
IRAD 900
RADAR
DETECTOR
Your rear
view
mirror
has
minimal
clearance between the back side
of
the
mirror
and
the
mirror
stem.
It
is
very Important
that
this
mount
ls
installed
correctly
to
ensure
mirror
adjustabillty is retained.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT
NOTE: For illustratlon purposes, the mount and rear view mirror shown
in
these instructions may look
slightly different then YOUR
mount
and rear view mirror.
BOTTOM
OF
SPRING
CLIP
IS
PARALLEL
WITH
RD
1 • The RELEASE Button
on
the radar detector (RD) Is NOT used with this
mount.
To
release the tension
of
the spring clip, simply squeeze the TRIGGER and the back side
of
the mount together. This will lower the bottom portion
of
the spring clip allowing you to
2 • The bottom
of
the spring clip must be parallel with the
top
of
the RD to slide in and out. SLIDE THE RD ONTO
THE
SPRING CLIP
AS
FAR AS IT WILL
GO
. Release the
trigger to secure the RD onto the mount. Before installing the
mount onto your rear view mirror, remove and install the RD a
few times so you can observe how the spring clip functions.
slide the RD on and off. When used property, the spring clip avoids putti
ng
excessive
pressure on the mirror stem when installing and removing the
RD
. The top portion
of
the mount should barely move when the two opposing forces are applied.
TOP
SECTION
MID
SECTION _
_.
.._
BODY
ASSEMBLY
CLEARANCE
FOR
MIRROR
~-
-
STEM
3.
The BODY ASSEMBLY must be removed to gain access to the
CLAMP SCREW. Remove the two socket head screws as shown
above. Be sure to remove the lock washer with the top screw along with
the lock washer and flat washer with the bottom screw. Loosen the
CLAMP SCREW so there is enough clearance between the TOP and
MID SECTIONS to slide over the mirror stem.
Innovative Design
And
Precision Manufacturing
PIVOT
POINT
TOP AND MID
SECTIONS
MUST
TOUCH
AT THE PIVOT POINT
BEFORE CLAMP SCREW
IS FULLY TIGHTENED
4 -
Wh
ile sitting In the passenger seat, place the mount over the mirror
stem. Tighten the CLAMP SCREW until the mount starts to clamp onto the
mirror stem. As you are tightening the clamp
sc
r
ew
, MAKE SURE THE TOP
AND MID SECTIONS TOUCH AT THE PIVOT POINT. If they
do
not touch
at the pivot point.YOU HAVE
AN
INCOMPATIBLE MIRROR TYPE FOR
THIS MOUNT. Position the mount as far forward as it will go and parallel to
the bottom
of
the mirror before fully tightening.
PAGE 1 OF 2
BlendMount - US
PATENT#
D625,580 S, D656,811 S, D653,980 S
D690,245 S,
0690
,246 S,
0690
,247
Sand
other patents pending
Specyfikacje produktu
| Marka: | BlendMount |
| Kategoria: | Niesklasyfikowane |
| Model: | BCB-2025 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z BlendMount BCB-2025, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane BlendMount
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
Instrukcje Niesklasyfikowane
- Thor
- Maytronics
- Legends
- Varad
- Geneva
- Colt
- Enviroswim
- Moog
- Samlex
- Micsig
- GoXtreme
- Honda
- Ibm
- Hifonics
- Maxi-Cosi
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025