Instrukcja obsługi BlendMount BCB-3030
BlendMount
Niesklasyfikowane
BCB-3030
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BlendMount BCB-3030 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 21 osób i została oceniona przez 11 użytkowników na średnio 4.3 gwiazdek
Strona 1/2
PART# BCB-3030
Blend
fflaunt®
&cobra
~111m~
11
111
11
Innovative
Mounting
Solutions
.,
28028
47415
LEFT HAND DRIVE VEHICLE
INSTALLATION INSTRUCTIONS FOR THE COBRA DSP-9200BT, SPX-7800BTn700, SPX-6700, AND iRAD 900
RADAR
DETECTOR
Your rear
view
mirror
has minimal clearance between the
back
side
of
the
mirror
and the
mirror
stem. It
is
very
important
that
this
mount
is
installed
correctly
to
ensure
mirror
adjustability
is
retained.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT
NOTE:
For
illu
tration
purposes,
the
mount
and
rear
view
mirror
shown
in
these
instructions
may
look
slightly
different
then
YOUR
mount
and
rear
view
mirror.
BOTTOM OF SPRING CLIP
IS PARALLEL WITH RD
1 - The RELEASE Button on the radar detector (RD) is NOT used with this mount.
2 - The bottom
of
the spring clip must be parallel with the
top
of
the RD to slide in and out. SLIDE THE
RD
ONTO
THE SPRING CLIP AS FAR AS IT WILL GO. Release the
trigger to secure
the
RD
onto
the
mount Before installing the
mount onto your rear view mirror, remove
and
install the
RD
a
few times
so
you
can
observe how the spring clip functions.
To
release
the
tension of the spring clip, simply squeeze the TRIGGER
and
the back
side
of
the
mount together. This will lower
the
bottom portion of
the
spring clip allowing
you
to
slide the
RD
on
and
off.
When
used
properly, the spring clip avoids putting excessive
pressure
on
the
mirror
stem
when
installing
and
removing
the
RD.
The top portion
of
the mount hould barely move when the two opposing forces are applied.
TOP
SECTION
MID
SECTION
---
lllilll
BODY
ASSEMBLY
CLEARANCE
FOR MIRROR
STEM
3 •
The
BODY ASSEMBLY must
be
removed
to
gain access
to
the
CLAMP
SCREW.
Remove the two socket head screws
as
shown
above.
Be
sure
to
remove the lock washer with the top screw
along
with
the
lock washer and flat washer with
the
bottom
screw.
Loosen
the
CLAMP
SCREW so
th
re
Is
enough clearance between the
TOP
and
MID
SECTIONS
to
slide over the mirror
stem
.
Innovative D sign
And
Precision Manufacturing
PIVOT
POINT
TOP AND MID
SECTIONS
MUST
TOUCH
AT THE PIVOT POINT
BEFORE CLAMP SCREW
IS FULLY TIGHTENED
4 - While sitting
in
the
passenger seat, place the mount over the mirror
stem.
Tighten
the
CLAMP SCREW until the mount starts to damp onto the
mirror stem.
As
you
are tightening
the
clamp screw, MAKE SURE THE TOP
AND MID SECTIONS TOUCH
AT
THE PIVOT POINT. If they do not touch
at
the
pivot point.YOU HAVE
AN
INCOMPATIBLE MIRROR TYPE FOR
THIS MOUNT. Position the mount
as
far forward
as
it will go
and
parallel
to
the bottom of
the
mirror before fully tightening.
PAGE 1 OF 2
BlendMount -
US
PATENT# D625,580
S,
D656,811
S,
D653
,
980
S
D690,245 S, D690,246 S,
D690
,247 Sand other patents pending
Specyfikacje produktu
| Marka: | BlendMount |
| Kategoria: | Niesklasyfikowane |
| Model: | BCB-3030 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z BlendMount BCB-3030, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane BlendMount
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
Instrukcje Niesklasyfikowane
- AeroCool
- BEA
- SEH
- Taqua
- Prem-i-air
- Merlin
- Giardino
- HQ Power
- BBB
- Gossen
- Lanaform
- Tryton
- Dr. Browns
- Meross
- ID-Tech
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025