Instrukcja obsługi BlendMount BMX-2025
BlendMount
Niesklasyfikowane
BMX-2025
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BlendMount BMX-2025 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 12 osób i została oceniona przez 6.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/2
PART# BMX-2025
Hlend
lllount-®
ESCORr
PASSPORT
MAX
LEFT HAND DRIVE VEHICLE
7
lll~!l~IJ
t
~,
1
11
111
1
11
5
Innovative
Mounting
Solutions
INSTALLATION INSTRUCTIONS FOR
THE
ESCORT PASSPORT MAX RADAR DETECTOR
Your rear
view
mirror
has minimal clearance between the back side
of
the
mirror
and the
mirror
stem. It
is
very
important
that
this
mount
is
installed correctly
to
ensure
mirror
adjustability
is
retained.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT
NOTE:
For
illustration
purposes, the
mount
and rear
view
mirror
shown
in
these
instructions
may
look
slightly
different
then YOUR
mount
and
rear
view
mirror.
BOTTOM
OF
SPRING CLIP
IS
PARALLEL
WITH
RD
1 • The
RELEASE
Button
on
the
radar
detector
(RD)
is
NOT
used
with
this
mount
. 2 •
The
bottom
of
the
spring
clip
must
be
parallel
with
the
top
of
the
RD
to
slide
in
and
out.
SLIDE THE RD ONTO
THE SPRING
CLIP
AS FAR AS IT
WILL
GO
. Release the
trigger to secure the RD onto the mount. Before installing the
mount onto your rear view mirror, remove and install the RD a
few times so you can observe how the spring clip functions.
To
release the tension
of
the spring clip, simply squeeze the TRIGGER and the back side
of
the mount together. This will lower the bottom portion
of
the spring clip allowing you to
slide the RD on and
off
. When used properly, the spring clip avoids putting excessive
pressure on the mirror stem when installing and removing the RD. The
top
portion
of
the
mount
should
barely
move
when
the
two
opposing
forces
are
applied
.
TOP
SECTION
MID
SECTION
---
liillll
BODY
ASSEMBLY
CLEARANCE
FOR MIRROR
STEM
3 • The
BODY
ASSEMBLY must be removed
to
gain access to the
CLAMP
SCREW
. Remove the two socket head screws as shown
above. Be sure to remove the lock washer with the top screw along with
the lock washer and flat washer with the bottom screw. Loosen the
CLAMP SCREW so there is enough clearance between the TOP and
MID SECTIONS to slide
over
the mirror stem.
Innovative Design And
Precision Manufacturing
TOP
AND
MID
SECTIONS MUST TOUCH
AT
THE
PIVOT POINT
BEFORE CLAMP SCREW
IS FULLY TIGHTENED
4 • While sitting in the passenger seat. place the mount over the mirror
stem. Tighten the CLAMP
SCREW
until the mount starts to clamp onto the
mirror stem. As you are tightening the clamp screw, MAKE SURE THE TOP
AND MID SECTIONS TOUCH
AT
THE PIVOT POINT.
If
they do not touch
at the pivot point.YOU HAVE AN INCOMPATIBLE MIRROR TYPE FOR
THIS MOUNT. Position the
mount
as far forward as it will
go
and parallel to
the bottom
of
the mirror before fully tightening.
PAGE 1 OF 2
BlendMount • US
PATENT#
D625,580 S, D656,
811
S,
D653,980 S
D690,245 S, D690,246 S, D690,247 S and other patents pending
Specyfikacje produktu
| Marka: | BlendMount |
| Kategoria: | Niesklasyfikowane |
| Model: | BMX-2025 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z BlendMount BMX-2025, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane BlendMount
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
Instrukcje Niesklasyfikowane
- TV One
- Nearity
- Make Noise
- Lowrance
- MDT
- Sebo
- ANDYCINE
- Tiger
- GFB
- WeFix
- Beko
- Echowell
- Sangean
- Speed-Link
- Doro
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025