Instrukcja obsługi BlendMount BMX-2032
BlendMount
Niesklasyfikowane
BMX-2032
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla BlendMount BMX-2032 (2 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 17 osób i została oceniona przez 9 użytkowników na średnio 4.6 gwiazdek
Strona 1/2
PART# BMX-2032
Blend
fflaunt-®
ESCOR'C
PASSPORT
MAX
1111111111111111111111
I
nno
v
at
i
ve
Mount
i
ng
Solu
ti
on
s LEFT HAND DRIVE VEHICLE
. . INSTALLATION INSTRUCTIONS FOR
THE
ESCORT PASSPORT
MAX
RADAR DETECTOR
7
28028
44272
4
Your rear
view
mirror
has minimal clearance between the back side
of
the
mirror
and the
mirror
stem. It
is
very important
that
this
mount
is installed correctly
to
ensure
mirror
adjustability
is
retained.
PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLING THIS MOUNT
NOTE: For illustration purposes, the mount and rear view mirror shown
in
these instructions may look
slightly different then YOUR mount and rear view mirror.
BOTTOM OF SPRING CLIP
IS PARALLEL WITH RD
1 - The RELEASE Button on the radar detector (RD) is
NOT
used with this mount.
2 -
The
bottom
of
the spring clip
must
be parallel with the
top
of
the RD to slide in and out. SLIDE THE RD ONTO
THE
SPRING CLIP AS FAR
AS
IT WILL
GO
. Release the
trigger
to
secure the RD onto the mount. Before installing the
mount onto
your
rear view mirror, remove and install the RD a
few times so you can observe
how
the spring clip functions.
To
release the tension
of
the spring clip, simply squeeze the TRIGGER and the back side
of
the mount together. This will lower the bottom portion
of
the spring clip allowing you to
slide the RD on and off. When used properly, the spring clip avoi
ds
putting excessive
pressure on the mirror stem when installing and removing the RD. The top portion
of
the mount should barely move when the two opposing forces are applied.
3 • The
BODY
ASSEMBLY must be removed to gain access to the
CLAMP SCREW. Remove the two socket head screws as shown
above. Be sure to remove the lock washer with the top screw along with
the lock washer and flat washer with the bottom screw. Loosen the
CLAMP SCREW so there is enough clearance between the TOP and
MID SECTIONS to slide
over
the mirror stem.
Innovative D ign
And
Precision Manufacturing
ROTATING
ADJUSTMENT
SCREW
TOPANDMID
SECTIONS
MUST
TOUCH
AT THE PIVOT POINT
BEFORE CLAMP
SCREW
IS FULLY TIGHTENED
4 - While sitting in the passenger seat, place the mount over the mirror
stem. Tighten the CLAMP
SCREW
until the mount starts to clamp onto the
mirror stem. As you are tightening the clamp screw, MAKE SURE THE TOP
AND
MID SECTIONS TOUCH AT THE PIVOT POINT.
If
they
do
not touch
at
the pivot point.YOU HAVE
AN
INCOMPATIBLE MIRROR TYPE FOR
THIS MOUNT. Position the mount as
far
forward as it will go and parallel to
the bottom
of
the mirror before fully tightening.
PAGE 1
OF
2
BlendMount -
US
PATENT#
D625,580 S, D656,811 S, D653,980 S
D690,245 S, D690,246 S, D690,247
Sand
other patents pending
Specyfikacje produktu
| Marka: | BlendMount |
| Kategoria: | Niesklasyfikowane |
| Model: | BMX-2032 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z BlendMount BMX-2032, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane BlendMount
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
30 Września 2024
Instrukcje Niesklasyfikowane
- Shimbol
- PreSonus
- Neo
- Sport Dog
- INOGENI
- Sound Machines
- EarFun
- Elite
- Samson
- MB Quart
- Godex
- Miele
- Commercial Chef
- Clatronic
- Silk'n
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025