Instrukcja obsługi Boss Super Over Drive SD-1
Boss
nieskategoryzowany
Super Over Drive SD-1
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Boss Super Over Drive SD-1 (1 stron) w kategorii nieskategoryzowany. Ta instrukcja była pomocna dla 38 osób i została oceniona przez 19.5 użytkowników na średnio 4.2 gwiazdek
Strona 1/1
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (supplied on a separate sheet).
After reading, keep the document(s) where it will be available for immediate reference.
INPUT jack
This jack accepts input signals (coming from a guitar, some other musical
instrument, or another eects unit).
* The INPUT jack also serves as the power
switch. Power is turned on whenever
a plug is inserted into the INPUT jack,
and is turned o when the plug is
disconnected. When not using the
unit, you should disconnect any cord
connected to the INPUT jack.
AC Adaptor
(PSA series; sold separately)
Electric Guitar
English
LEVEL knob
This knob adjusts the level of the eect sounds. Set the knob so there is no
volume dierence between the eect and straight guitar sounds.
Unlike earlier fuzz units, the SD-1 can faithfully express the picking dynamics and subtle nuances of your playing. Regardless of the type of guitar you’re using, the true character of its tone will come through.
This unit generates a soft and clear distortion like that of an overdriven tube amp.
In addition, you can use the tone control to boost or cut the high-frequency range, creating a versatile range of eects.
When the eect is on, the LED is lit, showing at a glance whether the eect is on or o.
OUTPUT jack
The output jack is used to connect the unit to
ampliers or other devices.
Guitar Amplier
DC IN jack
Accepts connection of an AC Adaptor (PSA series; sold separately). By using an AC Adaptor, you can play
without being concerned about how much battery power you have left.
* We recommend that you keep batteries installed in the unit even though you’ll be powering it
with the AC adaptor. That way, you’ll be able to continue a performance even if the cord of the
AC adaptor gets accidentally disconnected from the unit.
* Use only the specied AC adaptor (PSA-series).
* If the AC adaptor is connected while power is on, the power supply is
drawn from the AC adaptor.
CHECK indicator
This indicator shows whether an eect is ON/OFF, and doubles as the Battery Check indicator.
The indicator lights when an eect is ON.
* If this indicator goes dim or no longer lights while an eect is ON, the battery is near
exhaustion and should be replaced immediately.
* The CHECK indicator shows whether the eect is on or o, and indicates the dierent
functions. It does not indicate whether the power to the device is on or not.
TONE knob
This adjusts the tone of sound. Rotating it clockwise will create sharp sound
with emphasized treble, while turning it counterclockwise will create soft
sound with cut treble.
Pedal Switch
This switch turns the eects ON/OFF.
Thumbscrew
When this screw is loosened, the pedal will open, allowing you to change the
battery.
* For instructions on changing the battery, refer to “Changing the
Battery.”
Panel Descriptions
Main Features
Copyright © 2016 ROLAND CORPORATION
* To prevent malfunction and equipment failure, always turn down the volume, and turn o all the units before making
any connections.
* Before turning the unit on/o, always be sure to turn the volume down. Even with the volume turned down, you might
hear some sound when switching the unit on/o. However, this is normal and does not indicate a malfunction.
DRIVE knob
Adjusts the amount of overdrive. Turning the knob clockwise increases the
eect (distortion).
Owner’s Manual
Operating the Unit
1. After connecting all cords required, set all knobs on
the panel as illustrated.
2. Depress the pedal switch. Check LED lights to indicate
“EFFECT ON” and extinguishes to indicate “EFFECT
OFF.”
* This check LED is also used to check battery. If LED fails to light or
becomes dim, the battery should be replaced.
3. Turn DRIVE knob to proper position.
4. While switching pedal ON and OFF, turn LEVEL knob
to proper position so no volume dierence between
Normal and Eect modes is noticed.
5. Turn TONE knob to proper position.
Use of Battery
* A battery was installed in the unit before it left the factory. The
life of this battery may be limited, however, since its primary
purpose was to enable testing.
* If you handle batteries improperly, you risk explosion and uid
leakage. Make sure that you carefully observe all of the items
related to batteries that are listed in “USING THE UNIT SAFELY”
and “IMPORTANT NOTES” (supplied on a separate sheet).
* When operating on battery power only, the unit’s indicator will
become dim when battery power gets too low. Replace the
battery as soon as possible.
* Batteries should always be installed or replaced before
connecting any other devices. This way, you can prevent
malfunction and damage.
Changing the Battery
1. Hold down the
pedal and loosen
the thumbscrew,
then open the
pedal upward.
* The pedal can be
opened without
detaching the
thumbscrew
completely.
2. Remove the old
battery from the
battery housing,
and remove the snap cord connected to it.
3. Connect the snap cord to the new battery, and place
the battery inside the battery housing.
* Be sure to carefully observe the battery’s polarity (+ versus -).
4. Slip the coil spring onto the spring base on the back of
the pedal, and then close the pedal.
* Carefully avoid getting the snap cord caught in the pedal, coil
spring, and battery housing.
5. Finally, insert the thumbscrew into the guide bush
hole and fasten it securely.
Main Specications
BOSS SD-1: SUPER OverDrive
Nominal Input Level -20 dBu
Input Impedance 1 MΩ
Nominal Output Level -20 dBu
Output Impedance 1 kΩ
Recommended Load
Impedance
10 kΩ or greater
Power Supply DC 9 V: Dry battery 6F22 (9 V) type (carbon),
AC Adaptor (PSA-series: optional)
Current Draw 10 mA (DC 9 V)
* Expected battery life under continuous use:
Carbon: 60 hours, Alkaline: 90 hours
These gures will vary depending on the
actual conditions of use.
Dimensions 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H)inches
Weight 360 g / 13 oz (including battery)
Accessories Owner’s Manual, Leaet (“USING THE UNIT
SAFELY,” “IMPORTANT NOTES,” and “Informa-
tion”), Dry battery/9 V type (6F22)
Options AC adaptor (PSA-series)
* 0 dBu = 0.775 Vrms
* This document explains the specications of the product at the
time that the document was issued. For the latest information,
refer to the Roland website.
Thumbscrew
Battery Housing
Pedal
Spring Base
Coil Spring
Guide Bush
Hole
Battery Snap
Cord
Battery
Snap
9 V Battery
* 5 1 0 0 0 5 5 1 5 5 - 0 2 *
Specyfikacje produktu
| Marka: | Boss |
| Kategoria: | nieskategoryzowany |
| Model: | Super Over Drive SD-1 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Boss Super Over Drive SD-1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje nieskategoryzowany Boss
30 Czerwca 2024
29 Maja 2024
28 Maja 2024
26 Maja 2024
24 Maja 2024
23 Maja 2024
22 Maja 2024
21 Maja 2024
18 Maja 2024
17 Maja 2024
Instrukcje nieskategoryzowany
- Røde
- Ashly
- HDFury
- RIKON
- Oreck
- Smart-AVI
- Line 6
- Empress Effects
- Campart
- Infinity
- Axxess
- AG Neovo
- Warm Audio
- Scotsman
- WyreStorm
Najnowsze instrukcje dla nieskategoryzowany
28 Października 2024
28 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024
27 Października 2024