Instrukcja obsługi Brother LX-570
Brother
System laminowania
LX-570
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Brother LX-570 (9 stron) w kategorii System laminowania. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 5 użytkowników na średnio 4.3 gwiazdek
Strona 1/9
Cutter. The cutter is for trimming the
backing material and slides on the
cutter bar. It can be replaced.
Knob
Cutter bar
Latch (opens top cover)
Feed Deck. The LX-570 is designed for
use with items up to five inches wide. It
works best with item thicknesses
between 20 pound bond paper and 100
pound card stock or construction paper
(min. thickness is 0.004 inches, max.
thickness is 0.010 inches).
The LX-570 applies an adhesive, laminate, or
magnetic backing to an item without using heat or
electricity. You choose a backing by swapping the
drop-in cartridge.
The LX-570 comes with a starter cartridge already
installed. This cartridge applies a permanent
adhesive backing and is shorter than replacement
cartridges.
See the reverse for available cartridges and for
application ideas on using your LX-570. First, take a
few minutes to read these instructions.
Top Cover. Your LX-570
comes with a "starter"
cartridge already
installed, which applies a
permanent adhesive
backing to an item.
Cut:
When the item clears the cutter at the exit
area, gently push down on the cutter knob
and slide it all the way to the left or right.
Insert the item:
Insert the item face up at the feed
deck and turn the knob in the direction
of the arrows only; do not turn knob
backwards.
To avoid wasting the backing material,
note the location of the cut. Feed only
enough material to clear the cutter.
How to Use the LX-570
Insert the item
and be sure it
is straight.
Insert until you
feel contact;
then release it
as you turn
knob.
Exit area
When Using the
Starter Cartridge...
Feed and cut the item as described here. Be
sure to feed face up.
Press down firmly around all the edges. This
action prevents adhesive from remaining on
the front of the item. Then remove the clear
film and discard carefully as it is sticky.
When you are ready to place the item on a
surface, peel it from the white backing.
This starter cartridge contains five feet of
backing material. After you use it a few times,
always make certain that it contains sufficient
material. If uncertain, install a new cartridge
to avoid partial processing.
Note: the starter cartridge is shorter than the
replacement cartridges. See the other side
for cartridge descriptions and lengths. Always
consult packaging of replacement cartridges.
User’s Guide
12
LX-570 About the LX-570
Feed straight, not at an angle.
Turn the knob forward only.
Notes:
Before using, remove the protective tape
and other packaging materials under the
top cover.
Under the terms of an agreement with
Xyron, Inc., the purchase or
other acquisition of this product confers
no right or license to use
the product in the Retroreflective Field.
Specyfikacje produktu
| Marka: | Brother |
| Kategoria: | System laminowania |
| Model: | LX-570 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Brother LX-570, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje System laminowania Brother
6 Września 2024
4 Września 2024
27 Sierpnia 2024
23 Sierpnia 2024
20 Sierpnia 2024
16 Sierpnia 2024
Instrukcje System laminowania
- Tracer
- Exibel
- Pavo
- Konig
- Nedis
- Marquant
- Royal Sovereign
- Powerfix
- Peach
- Ednet
- GBC
- Hama
- Rexel
- United Office
- Sencor
Najnowsze instrukcje dla System laminowania
2 Marca 2025
9 Lutego 2025
9 Stycznia 2025
4 Stycznia 2025
4 Stycznia 2025
5 Grudnia 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024