Instrukcja obsługi Craftsman CMXPTSG1004NB

Craftsman Niesklasyfikowane CMXPTSG1004NB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Craftsman CMXPTSG1004NB (46 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 18 osób i została oceniona przez 9.5 użytkowników na średnio 4.8 gwiazdek

Pobierz PDF

Strona 1/46

1/2-in 400-ft-lb Impact Wrench

Clé à chocs de 1/2 po et de 400 lb-pi

Llave de percusión de 1/2 pulg. y 55,3 kgf-m

CMXPTSG1004NB

IN CT N U D’ I T U D N R NESSTRU IO MAN AL | GUIDE UTIL SA ION | MAN AL E I ST UCCIO

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

1 1 WWW.CRA M COM-888-33 -4569 FTS AN.

ENGLISH

Fig. A

Deﬁnitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to

hazardous situations and your risk of personal injury or property damage.

DANGER ll: wi Ind cates an y h us sit n wh t ai imminentl azardo uatio ich, oif n voided, result in

death or serious injury.

WARNING could: Ind cates a potentially h us sit n wh t ai azardo uatio ich, oif n voided, result

in .death or serious injury

CAUTION may: Ind cates a potentially h us sit n wh t ai azardo uatio ich, oif n voided, result in

minor or moderate injury.

NOTICE may: Ind cates a practice wh t ai not related to personal injury ich, oif n voided,

result in property damage.

( i u ord ica a l d e.Used w tho t w ) Ind tes a s fety re ate messag

WARNING: Read all safety warnings and all

i i nstruct ons. Fa lilure to fo low the warnings

an nstr ct t d i u i lons may resu in electric shock, ﬁre

a or serious injury.nd/

WARNING: Never mod fy the i product or any

pa . Damage or personal injury could result.rt of it

WARNING: T c i f , e o redu e the r sk o injury read th

instruction manual.

If you have any questions or comments about

this or any product, call CRAFTSMAN toll free

at: 1-888-331-4569.

Components

11/2 in. Impact Wrench

2 Anvil

3Trigger

4Torque Setting Switch

5Air Inlet

1/2-in 400-ft-lb Impact Wrench

ENGLISH

WARNING: Failure to observe and follow safety instructions could result in injury or death.

WARNING: Improper operation or maintenance of this tool could result in serious injury

and property damage. Read and understand all warnings and operation instructions before

using this tool. When using any tool, basic safety precautions should always be followed to

reduce the risk of personal injury. Anticipate and be alert for sudden changes in motion

during startup and operation of any power tool. Do not operate tool if trigger does not turn

the tool on or oﬀ. Do not use this tool at heights exceeding 6 feet (2m). Use each tool for its

intended function only. Do not use this product in unsafe work conditions. It is always

recommended to keep a ﬁre extinguisher and ﬁrst aid kit near work areas.

WARNING: User must also read the compressor manual and follow all compressor safety

instructions

CMXPTSG1004NB

Speciﬁcations

Model CMXPTSG1004NB

Drive 1/2" 12.7 ( mm)

Free Speed 10,000 rpm

Maximum Torque 400 ft.-lbs.

Average Air Consumption 5 scfm

Air Inlet 1/4" npt

Air Hose 3/8" (9.53 mm)

Working Pressure 90 psi

Compressor requirements

IMPORTANT: To operate correctly, this tool requires airﬂow of at least 5 Standard Cubic Feet

per Minute (SCFM) at 90 Pounds per Square Inch (PSI) at the tool. The air hose length could

aﬀect how much air pressure the tool is actually receiving. You may need to adjust the air

pressure higher on the air regulator to achieve the working pressure of 90 PSI.

™

5 @ 90 SCFM PSI

Tool Requirements

Exigences relatives aux outils

Requisitos de herramientas

Specyfikacje produktu

Marka:	Craftsman
Kategoria:	Niesklasyfikowane
Model:	CMXPTSG1004NB
Częstotliwość wejściowa AC:	50 Hz
Napięcie wejściowe AC:	220-240 V
Wysokość produktu:	1100 mm
Szerokość produktu:	780 mm
Głębokość produktu:	940 mm
Waga produktu:	19400 g
Regulacja wysokości:	0 - 85 mm
Moc pobierana:	2000 W
Średnica tarczy:	250 mm
Prędkość biegu jałowego (max):	5000 RPM
Głębokość cięcia przy (90º):	-, 85 mm
Prędkość biegu jałowego:	5000 RPM
Otwór ostrza:	30 mm
Maksymalna wysokość cięcia:	85 mm
Liczba zębów:	24
Szerokość stołu:	642 mm
Głębokość stołu:	485 mm
Otwór wrzeciona:	30 mm