Instrukcja obsługi CyberPower MP1044NN

CyberPower Niesklasyfikowane MP1044NN

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CyberPower MP1044NN (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 9 osób i została oceniona przez 5 użytkowników na średnio 4.3 gwiazdek

Pobierz PDF

Strona 1/1

YOUR ULTIMATE ALLY IN POWER

6-OUTLET POWER STRIP

TWIN PACK

MP1044NN

USER MANUAL

FEATURES

1. ON/OFF Reset Switch Breaker

Control power to all outlets. The switch is also a 15A

breaker. When an overload occurs, it will automatically

switch o. To resume operation, ensure the overload

condition is corrected and reset the surge protector by

switching the unit ON.

2. Six Standard Outlets

3. 2-ft. Power Cord

4. Keyhole Mounting Slots (on back)

SPECIFICATIONS

Model Number: MP1044NN

Outlets: 6 Standard Outlets

Electrical Rating: 125V / 15A / 1875W

Response Time: Less than 1 nanosecond

Circuit Breaker: 15 Amp

i WARNING: This product can expose you to chemicals including bisphenol A (BPA)

and styrene (ABS), which is known to the State of California to cause reproductive

harm and cancer. For more information, go to www.P65Warnings.ca.gov..

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK:

Use only in dry locations and only indoors.

DO NOT plug into another relocatable power tap.

DO NOT “daisy chain” surge protectors.

DO NOT use with any aquarium equipment.

DO NOT use if properly grounded outlets are not available.

DO NOT install this device if there is less than 10 meters (30 feet) of wire between

the electrical outlet and electrical service panel.

DO NOT use for medical or life support equipment. This device features an internal

protection that will disconnect the surge protective component at the end of its

useful life, but it will maintain unprotected power to the load.

TROUBLESHOOTING

If the ON/OFF is switched o, the 15 AMP circuit breaker may have tripped.

Examine your connected equipment and remove the device that is overloading

the circuit. Then, turn the ON/OFF switch back to RESET.

TECHNICAL SUPPORT

FOR MORE INFORMATION

Visit CyberPowerSystems.com for more information regarding: Visit: CyberPowerSystems.com/support

• Product information and certiﬁcations Toll-Free: 1-877-297-6937

• Product warranty Hours of Operation: Monday - Friday: 7:00am - 6:00pm CST

All other trademarks are the property of their respective owners.

CONFORMANCE APPROVALS harmful interference in a residential installation. This equipment • Reorient or relocate the receiving antenna.

This device complies with Part 15 of the FCC Rules. generates, uses, and can radiate radio frequency energy and, if not • Increase the separation between the equipment and receiver.

Operation is subject to the following two conditions: (1) this installed and used in accordance with the instructions, may cause • Connect the equipment into an outlet on a circuit dierent from

device may not cause harmful interference, and (2) this device must harmful interference to radio communications. that to which the receiver is connected.

accept any interference received, including interference that may However, there is no guarantee that interference will not occur in a • Consult the dealer or an experienced radio/TV technician for help.

Cyber Power Systems (USA), Inc. cause undesired operation. particular installation. If this equipment does cause harmful interfer-

This equipment has been tested and found to comply with the limits ence to radio or television reception, which can be determined by WARNING: Changes or modiﬁcations not expressly approved by the

4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 for a Class B digital device, pursuant to Part 15 of the FCC Rules. turning the equipment o and on, the user is encouraged to try to party responsible for compliance could void the user’s authority to

These limits are designed to provide reasonable protection against correct the interference by one or more of the following measures: operate the equipment.

CyberPowerSystems.com