Instrukcja obsługi DeWalt DS302
DeWalt
Niesklasyfikowane
DS302
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DeWalt DS302 (8 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 16 osób i została oceniona przez 8.5 użytkowników na średnio 5.0 gwiazdek
Strona 1/8
DS300 Jobsite Security Cable Lock
DS302, DS306, DS312 and DS324
Replacement Cables
WARNING: Read and understand all instructions and
warnings for this product. In addition, read and follow all
instructions and warnings provided with the DS100 Jobsite Security
Portable Alarm System.
CAUTION: DANGER OF EXPLOSION, INJURY, OR FIRE.
Carefully follow all instructions and warnings on the battery label and
package.
• Never use a damaged or worn out battery.
• Discharged batteries should be replaced only with type CR-123 3.0
Volt Lithium batteries.
• Do not use re-chargeable batteries or attempt to charge batteries.
• Carefully remove the old, discharged battery.
• Do not attempt to open.
• Do not peel the label from the battery.
• Never dispose of a battery in a fire.
• Dispose of used batteries in accordance with local regulations.
• Recycle batteries.
• Always insert batteries correctly with regard to polarity (+ and -)
marked on the battery and the equipment.
• When installing the battery, do not use excessive force. If the bat-
tery does not fit, check to make sure that it matches the polarity
markings.
• Never expose the battery terminals to any other metal object. This
can short circuit the battery.
• Avoid exposure to temperature extremes.
• When not in use, store the battery in a cool, dark, dry place.
• Keep batteries out of reach of children.
FCC REGULATORY STATEMENT (FCC: HCQ3B6ETUMXM)
• This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) the device must accept any
interference received, including interference that may cause unde-
sired operation.
INDUSTRY CANADA (IC: 2309A-ETUMXM)
•NOTICE: This equipment meets the applicable Industry Canada
Terminal Equipment Technical Specifications. This is confirmed
by the registration number. The abbreviation, IC, before the reg-
istration number signifies that registration was performed based
on a Declaration of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that Industry
Canada approved the equipment.
Important
• The Cable Lock needs to be removed before operating the
attached equipment.
• The Cable Lock uses a cable with a stainless steel braid. If the
exterior coating is cut, torn or abraded, the exposed metal could
short out equipment. Immediately replace the cable. Replacement
cables [2' (.61m), 6' (1.83m), 12' (3.66m) and 24' (7.32m) lengths]
are available as an additional accessory.
• To avoid constant unsecured alarms, be sure that the Cable Lock
is closed while it is not being used.
• Inspect the gasket whenever the housing is opened and replace if
worn or damaged. Be sure the gasket is in the proper position
before closing the housing.
• This product is designed for indoor/outdoor use.
Components
A. Gasket F. Tamper
B. Inner housing G. Battery
C. Outer housing H. Screws
D. Cable lock lever I. Replaceable cable
E. Reset button
Product Function
The DS300 Jobsite Security Cable Lock is a 12' (3.66m) cable impreg-
nated with a heavy duty urethane jacket over stainless steel braiding
which provides strength, durability and flexibility. As the cable ends are
disconnected, the system will be notified of an unsecured device.
Once activated, this device will work exclusively with the assigned
DS100 Jobsite Security Portable Alarm System.
1. The DS300 contains a locking mechanism with a location for a
standard padlock (not included) to provide additional security. The
addition of a padlock is recommended.
2. The DS300 features a tamper that notifies the system when the
cover has been opened.
3. The DS300 features 900 MHz spread spectrum communication
with the Base Unit allowing for a range of up to 2000' (610m).
NOTE: Metal objects blocking radio frequency (RF) transmission can
affect the range of the sensor.
Prevention of False Alarms
The majority of alarms that occur are false. These situations happen
every day due to user error, incorrect installation or improper mainte-
nance of the system. False alarms will limit the responsiveness to the
SITELOCK LLC, 626 Hanover Pike, Hampstead, MD 21074 (MAR05) Form No. 626136-01 DS300 Copyright © 2004, 2005 DEWALT
CAUTION: POTENTIAL EQUIPMENT
MALFUNCTION OR FAILURE. Do not
touch the electronic components inside
the device, except the reset button and
battery.
CAUTION: POTENTIAL EQUIPMENT
MALFUNCTION OR FAILURE. If exterior
coating is damaged and the metal is
exposed, the secured equipment could
short out.
JD
J
H
D
EF
D
M
I
C
A
B
G
FIG. 1
KLFIG. 3
FIG. 2
Specyfikacje produktu
| Marka: | DeWalt |
| Kategoria: | Niesklasyfikowane |
| Model: | DS302 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z DeWalt DS302, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane DeWalt
3 Stycznia 2025
3 Stycznia 2025
3 Stycznia 2025
3 Stycznia 2025
2 Stycznia 2025
2 Stycznia 2025
11 Grudnia 2024
11 Grudnia 2024
11 Grudnia 2024
11 Grudnia 2024
Instrukcje Niesklasyfikowane
- GPO
- Bracketron
- Hapro
- Qubino
- Astera
- Cool Maker
- Nowsonic
- G-Technology
- SinuPulse
- CaterChef
- WHALE
- HealthPostures
- Forza
- Saitek
- Cooper Lighting
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025