Instrukcja obsługi DeWalt DW7353

DeWalt Niesklasyfikowane DW7353

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DeWalt DW7353 (3 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 15 osób i została oceniona przez 8 użytkowników na średnio 4.9 gwiazdek

Pobierz PDF

Strona 1/3

DW7353

CHIP COLLECTION ACCESSORY

WARNING: For your own safety, read the tool instruction manual

before using any accessory. Failure to heed these warnings may result

in personal injury and serious damage to the planer and the acces-

sory. When servicing this tool, use only identical replacement parts.

Unpacking the Chip Collection Kit

In addition to these instructions, the carton should contain:

• 1 chip collector with 4" hose with drum bonnet and 1 hose clamp

with ground wire attached

Assembly

WARNING: TURN OFF AND UNPLUG PLANER BEFORE

MAKING ANY ADJUSTMENTS OR REMOVING OR INSTALLING

ATTACHMENTS OR ACCESSORIES.

TO ATTACH THE ROUND DUST PORT TO THE PLANER (FIG. 1)

1. Depress the lock button (A) on the chip ejection chute (B), shown

in Figure 1.

2. Slide the notches in the round dust port (C) over the pins on the

chip ejection chute (Fig. 2).

3. Rotate the round dust port until the button engages the dust

ejection chute and locks in place.

TO ATTACH THE HOSE AND GROUND WIRE TO

THE DUST PORT (FIG. 2)

WARNING: Do not use the chip collection accessory without

attaching the ground wire to the planer. Static electricity may create

sparks that would risk a fire hazard.

1. Fit the end of the chip ejection hose around the outside of the

round dust ejection port on the planer.

2. Tighten the screw on the clamp (D) to secure the hose to the port.

3. Attach the end of the ground wire (E) to one of the two screws on

the rear of the planer body (F).

TO ATTACH CHIP COLLECTOR TO THE

COLLECTION CONTAINER

1. Select a container with a rim or edge that the drawstring collar (G)

will attach to securely (Fig. 3).

2. Drape the drum bonnet (H) of the chip collector over the outside

rim of the container (Fig. 4).

3. Press the lock button (I) and pull the drawstring collar on the bag

as tight as possible to secure. Release the lock button to hold

drawstring in place.

WARNING: DON’T USE IN DANGEROUS ENVIRONMENT. Don’t

use power tools in damp or wet locations, or expose them to rain.

Keep work area well lighted. Always operate tool in a well-ventilated

area free of combustible materials, gasoline or solvent vapors. If

sparks come in contact with flammable vapors, they may ignite, caus-

ing fire or explosion.

WARNING: Clean out your tool often, especially after heavy

use. Dust and grit containing metal particles often accumulate on

interior surfaces and could create a risk of serious injury, electric

shock or electrocution. ALWAYS WEAR SAFETY GLASSES.

WARNING: Never clear clogs, make cutter knife replacement, or

any other repairs/adjustments with unit plugged in.

The Hose

NOTE: The hose measures 8' long. For proper air flow, suspend the

hose from above or cut the hose to length.

CAUTION: It is not recommended that the hose sag over the edge

of the collection container. The system may not work properly while

the bag is weighed down by the sagging hose.

The following are trademarks for one or more D EWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box

configuration; and the array of lozenge-shaped humps on the surface of the tool.