Instrukcja obsługi Dimplex RXRBTI
Dimplex
Niesklasyfikowane
RXRBTI
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Dimplex RXRBTI (1 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 10 osób i została oceniona przez 5.5 użytkowników na średnio 4.4 gwiazdek
Strona 1/1
Installation and Operating Instructions
TIDN60R001 Issue 0
RXTIRB - Runback Timer
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Installation
Switch the heater off and remove the plug-in protective cover
from the right hand side of the thermostat unit at the back of
the heater. Remove the Runback timer from it’s box, set the
required runback period as detailed below and plug the timer
into the slide in compartment now exposed. Switch the heater
on at the mains supply.
Note: In order to prevent the timer being removed from the
heater, fit the supplied
screw to hole at rear
of timer enclosure
after the timer has
been inserted. The
heater needs to be
removed from the wall
for this operation - see
Fig. 1.
This locks the timer to
the heater body.
Setting the Standard Runback Timer Function
The runback timer can
be set for a run period
from 30 minutes to 4
hours (30-minute
steps only). To set the
runback period on the
timer, adjust the dip
switches located at
the back of the timer -
see Fig. 2.
To set the desired runback period switches 2, 3 and 4 have to
be set either up or down according to Table 1. Switch 1 should
always be left down (È) to run the standard runback timer
function.
Table 1
1 2 3 4 Runback Period
È È È È ½ hour
È È È Ç 1 hour
È È Ç È 1½ hours
È È Ç Ç 2 hours
È Ç È È 2½ hours
È Ç È Ç 3 hours
È Ç Ç È 3½ hours
È Ç Ç Ç 4 hours
Starting theTimer
Once the unit has been inserted into the heater and the heater
is powered on, to start the runback timer the button at the top
of the plug in timer must be pressed. Once pressed, the
runback timer will switch on (the neon light on runback timer
will go on) for the runback period set previously.
Fig. 1
Stopping the Timer
To cancel the runback timer press the button at the top of the
timer. Once pressed the runback timer will turn the heating off
and the neon light will switch off.
Runback Timer’s special function
The special function runs in COMFORT mode for the runback
period selected. It then switches automatically to SETBACK
for 24hrs, after which it switches to FROST mode indefinitely.
When in COMFORT mode the heater operates at the user
selected temperature.
When in SETBACK mode the heater operates at 5°C below
the user selected temperature.
When in FROST mode the heater only switches on when the
ambient temperature of the heater is below 5°C, independent
of user selected temperature.
Setting the Runback Timer in Special function
mode
Set switch 1 to the up (Ç) position. Set the desired period by
setting the switches 2, 3 and 4 either up or down according to
Table 2.
Table 2
1 2 3 4 Runback Period
Ç È È È ½ hour
Ç È È Ç 1 hour
Ç È Ç È 1½ hours
Ç È Ç Ç 2 hours
Ç Ç È È 2½ hours
Ç Ç È Ç 3 hours
Ç Ç Ç È 3½ hours
Ç Ç Ç Ç 4 hours
Once the period has been set, the unit is plugged into the
heater and mains is switched on, the runback timer functions
as follows:
1. On initial power ON the runback timer causes the heater to
be permanently in FROST mode, the default setting, Runback
timer neon light is off.
2. The runback timer button, once pressed causes the heater
to run the COMFORT setting (light on), for the set runback
period selected. It then switches automatically to SETBACK
for 24hrs (light off), after which it switches to FROST mode
indefinitely.
Manually Selecting Setback and Frost modes
The SETBACK mode can be selected manually by pressing
the button on the top of the timer while the heater is in
COMFORT mode, the setback mode then operates for it’s 24
hour period after which it will switch automatically to FROST
mode. The FROST mode can be selected manually by
pressing the button on the top of the timer twice when the
heater is in COMFORT mode (or once when it is in SETBACK
mode), heater will remain in FROST mode.
ON
ON
ON
ON
ONON
DIP
DIP
DIP
DIP
DIPDIP
1
1
1
11
2
2
2
223
3
3
334
4
4
44
ON
ON
ON
ON
ONON
DIP
DIP
DIP
DIP
DIPDI P
1
1
1
11
2
2
2
223
3
3
334
4
4
44
REAR VIEW
screw
holes
runback
timer
Fig. 2
Specyfikacje produktu
| Marka: | Dimplex |
| Kategoria: | Niesklasyfikowane |
| Model: | RXRBTI |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Dimplex RXRBTI, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Niesklasyfikowane Dimplex
13 Stycznia 2025
30 Grudnia 2025
2 Października 2024
2 Października 2024
30 Września 2024
28 Września 2024
27 Września 2024
22 Września 2024
20 Września 2024
20 Września 2024
Instrukcje Niesklasyfikowane
- SafeMi
- Areca
- Sirus
- Becken
- Vaddio
- Cleanmaxx
- Egnater
- Sabrent
- Minolta
- KEF
- Hensel
- Farberware
- Amer
- Remington
- Pentair
Najnowsze instrukcje dla Niesklasyfikowane
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025
29 Stycznia 2025